Share your ICND1 v3.0 Experience

@PL413r

Please PL, your though for BREAFAST lol!!!

Q. Rerfer to the exhibit
Route# configure terminal
Router( config)#vlan 10
Router( config-vlan)#do show vlan

Q. Which statement describes the effect of this configuration?
A) The VLAN 10 VTP configuration is displayed
B) VLAN 10 spanning-tree output is displayed
C) The VLAN 10 configuration is saved when the router exits VLAN configuration mode?
D) VLAN is added to the VLAN database < ?

@Ned, ALSO regarding PRIVATE VLAN ( IN YOUR TEST! )

The private VLAN always has one primary VLAN. Within the primary VLAN you will find the promiscuous port. In my picture above you can see that there’s a router connected to a promiscuous port. All other ports are able to communicate with the promiscuous port. Within the primary VLAN you will encounter one or more secondary VLANs, there are two types:

Community VLAN: All ports within the community VLAN are able to communicate with each other and the promiscuous port.

Isolated VLAN: All ports within the isolated VLAN are unable to communicate with each other but they can communicate with the promiscuous port.

https://networklessons.com/switching/private-vlan-pvlan-cisco-catalyst-switch/

@CISCOTTE
This is not in ICND1 its ICND2 question
Q. If primary and secondary root switches with priority 16384 both experience catastrophic losses, which teritary switch can take over ?
A) switch with priority 20480?
B) switch with priority 8192
C) switch with priority 4096 ?
D) switch with priority 12288

Please PL, your though for BREAFAST lol!!!
Q. Rerfer to the exhibit
Route# configure terminal
Router( config)#vlan 10
Router( config-vlan)#do show vlan (you use this command to be able to run show command where its not supposed to be run, so it will output vlan 10 info)

Q. Which statement describes the effect of this configuration?
A) The VLAN 10 VTP configuration is displayed

@CISCOTTE
Sorry man, i didnt pay attention on on the command above do show vlan…
So if the vlan does not exist in the box it will create a new one
So right answer is
D) VLAN is added to the VLAN database < ?

@CISCOTTE
So If i wasnt clear enough

Route# configure terminal ! this enter global configuration
Router( config)#vlan 10 ! this create a new vlan 10 in case It wasn´t previous existent
Router( config-vlan)#do show vlan ! this will output of existent VLANs in the box

@PL413r

Thanks PL, but NO > Ned took the TEST(11/20/16 ) & had this Question!

Q. If primary and secondary root switches with priority 16384 both experience catastrophic losses, which teritary switch can take over ?
A) switch with priority 20480?
B) switch with priority 8192
C) switch with priority 4096 ?
D) switch with priority 12288

ANSWER >16384+4096 = 20480 ???? I READ SOMEWHERE & LOST THE LINK???????
I will research AGAIN & KEEP YOU POSTED B4 U TAKE YOUR TEST, I HOPE! lol!!!

@PL413r

SO IS IT 12:00pm into ” The Gungle Fever ” lol!!!! Lunch Time!!!

Sorry Jungle!!!!

@PL413

I JUST READ THIS:https://www.iana.org/numbers
Both IPv4 and IPv6 addresses are generally assigned in a hierarchical manner. Users are assigned IP addresses by Internet service providers (ISPs). ISPs obtain allocations of IP addresses from a local Internet registry (LIR) or National Internet Registry (NIR), or from their appropriate Regional Internet Registry (RIR):

Q.Wich entity assigns IPv6 addresses to end users?
A) ICANN
B)APNIC
C) RIR <?
D) ISP < ?

274q VCE says > RIR

I KNOW WE TALKED ALOT ABOUT IT B4!!!!

@ANY_ANY_ANY ONE who wants PINTCHING INTO THE CONVERSATION ARE WELCOME!!!!!!

@CISCOTTE
This is a SPANTREE question…can’t be in icnd1 but I believe the switch with smallest priority wins. If they all had the same priority it would compare the mac address to untie it! (default priority is 32768)

Q. If primary and secondary root switches with priority 16384 both experience catastrophic losses, which teritary switch can take over ?
A) switch with priority 20480?
B) switch with priority 8192
C) switch with priority 4096 X (smallest priority)
D) switch with priority 12288

CISCOTTE
Q.Wich entity assigns IPv6 addresses to end users?
A) ICANN
B)APNIC
C) RIR (wrong)
D) ISP (correct)

Who is responsible to give you an IP address when you buy internet? its your Internet Service Provider (comcast,at&t or whichever you have) or ISP.

Thanks PL is what originally I THOUGHT!!!!

AND YOU ARE 100% RIGHT ( ALWAYS! ) about ISP the KEY WORD IS: ” Assigns? ”
Those questions are ALWAYS DOUBLE TALK like they wants you to FAIL the TEST!!!!

Thanks PL Friend!!!!!

hayy!!!!

IANA give prefix to RIR 2002-> RIR give prefix to ISP 2001:db8-> ISP give prefix to COMPANY

2001:db8:acad–>COMPANY give the subnet 2001:DB8:ACAD:0001 to menagement vlan or 2001:DB8:ACAD:0002 to facilty vlan and so on. the last 64 bits from interface ID(host part )
user create for them self with eui64 process or windows generate one …. if you are privat user you gonna get whole prefix from ISP 2001:DB8:ACAD:0001 and the other parrt of address your windows is gonna create for you(: so the ansfer is D

when you have the exam CISCOTTE ? how much time you have left !!!! i have one good site who wonnt to learn its free no paying (:

@Starter

Thanks S!; Like I said the KEY is to make sure to READ between the Lines & Word during the TEST

The KEY up here is ” ASSIGNS ” just like say PL413r !!!! (Who is responsible to give you an IP address when you buy internet? its your Internet Service Provider (comcast,at&t or whichever you have) or ISP.)

@Starter

YOU ASK!!! ” How much time you have left !!!! ” I have to decided TODAY!!!

Thursday in Thanksgiving in ” TRUMP WORLD ” so I don’t wants to be the ” TURKEY “lol
Therefore it has to BEFORE or AFTER!!!

Regardless the Time left I have is always good to ‘ FEED THE BRAIN “Please, may you forward this FREE link!!!

Thanks again!!!!

How many IP’s can be assigned to an interface?
A.1
B.2
C.8
D.Unlimited

Which is the right answer? I am thinking unlimited due to being able to add secondary IP to an interface and I can find no limits to doing that? Can anyone provide further information?

@Anon

A. 1

I thought so… I had answered that but it made me feel like It was a trick question and sent me into research mode and discovered 2ndary IP’s on interface which can be an X amount.

passed yesterday with 864/1000
many questions can be found on this forum including dave package, same simulation he shared but different set of output is shown so different anwers
please dont ask as i dont remember questions but here is what i remember
both questions of 6to4 tunnel and cef question was there and i dont know the answers
total of 63 questions
274q mentioned earlier is pretty much valid

thanks and take care 9tut

also please dont waste a single penny on paid dumps, not worth it
you should to able to find enough free dumps to get you certified if you know your stuff

I am reviewing that 274q right now and seems to have same as 9tut so far, but my studying is at a slow pace trying to figure what I need to know, dumps are helping me review and get better educated and understanding.

@kabs

CONGRAT K!!!! And thanks for the WARNING!!!!!!lol

@kabs

Question: CEF is enabled what will be automatically disable
Answer: ????
– Fast switching
– RIP
– IP …

Maybe the answer is logging? I can’t find a clear answer in the text

Function Cisco Express Forwarding
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipswitch_cef/configuration/12-4t/isw-cef-12-4t-book/isw-cef-enable-disable.html

Q.If Cisco E.F. (CEF) is enable what will be AUTOMATICLY disable?
A) process switched mode that will be disabled

Function Cisco Express Forwarding
CEF is mainly used to increase packet switching speed by reducing the overhead and delays introduced by other routing techniques.

@Review
not sure about the answer but Fast switching was def. not available options otherwise i would hve chosen this

Q.If Cisco E.F. (CEF) is enable what will be AUTOMATICLY disable?
A) Fast switching <

I also have a question about the VLAN SIM:

Server1 and Server2 are unable to communicate with the rest of the network. Your initial check with system administrators shows that IP address settings are correctly configured on the server side. What could be an issue?

A. The VLAN encapsulation is misconfigured on the router subinterfaces. <<<
B. The Router is missing subinterface configuration.
C. The Trunk is not configured on the L2SW1 switch.
D. The IP address is misconfigured on the primary router interface.

What commands on the router would show an improper VLAN encapsulation?

Sh r

@review
show run

Then navigate to those sub interfaces to view their config.

Guys, i am getting confused here

Which command can you enter to verify that a 128-bit address is live and responding?
A. traceroute
B. telnet
C. ping
D. ping ipv6

In my opinion ANSWER (C) will also work but the dump says (D) is correct. I haven’t seen ping ipv6 being used anywhere in the ICND1 official book.

https: //ciscoexam. online/CCNA/200-125/269

@Starter

A unique local address (ULA) is an IPv6 address in the block fc00::/7 , defined in RFC 4193. It is the approximate IPv6 counterpart of the IPv4 private address

Pass your exam on first attempt.
These are valid exam questions. Visit below page and download dumps instant:

remove as-teriks
icnd1-2.blogspo*t.co*m

Passed with 930+
Will let you know what I remember later

@PL413r

PLLLLLLLLLLLLLLLLLLLLLLLLLLLL!!!!KUDO 2U My Friend!!!!

PS: WHEN is GOOD TIME 2Line2U???

@ALL
1- most of questions are in the 274 and Dave’s quiz.(90%+)
2- each lab had 4 questions to answer all like the questions question starting from 576 CISCOTTE posted. (had 2 or three labs with 4 questions each, take your time to understando them…since I finished it with @30 minutes left)
3- security labs were there with a computer conected via console to a router and another into a switch
4 – 3 subnets questions

Question: Successful Ping:
Answer:
This is not about seconds…you need to know that the “host sends a ping request and destination sends a echo reply”…many wrong questions were mixing this

Question: What is the ping character for a unknown packet
Answer: ? <- actual character

Question: a static route wasnt showing on routing table why?
Answer: interface was on shutdown condition

Question: Router # ip nat source list 1 interface ethernet 0 overload (2 questions alike)
Answer:
All machines will use the ip that is on that ethernet interface to go out

Questions: about host routes (3 or 4 questions)
Answer: you need to know that host routes have mask of /32 or 255.255.255.255…ex: ip route 192.168.0.1 255.255.255.255 s0/0/1

Question: ipv6/ipv4 migration mechanisms
Answer: dual stack (6to4 was an answer but i think it was wrong)

@ALL
had a ipv6 unique local but wasnt like the ones posted here!

Hi, just wondering if any of you have used dumps for the A+ 220 – 901 cert? Just studied for a month, pretty much know 3/4 of this exam but need dumps to guarantee a pass, if anyone can send me a trusted website/forum that would be Lovely.

=)

@Pl413r, Congratulations Man….Great Job and thanks for sharing. It helps a lot.

Could you please help me out with the following question.

Which command can you enter to verify that a 128-bit address is live and responding?
A. traceroute
B. telnet
C. ping
D. ping ipv6
In my opinion ANSWER (C) will also work but the dump says (D) is correct. I haven’t seen ping ipv6 being used anywhere in the ICND1 official book.

@PL413r

THANKS for the update PL!!! Again KUDO 2U!!!!!!

Hi Guys!

@shadows: It’s indeed D. An IPv6 address is 128bit long and only the ping ipv6 command can ping such addresses.

Regarding the Baby Giant Frame:
1 ) Which MTU size can cause a baby giant error? > 1518
2 ) Which MTU size can cause a baby giant error? > 1600 X

In my opinion, it cannot be 1600 as we are talking about MTU here.

A frame is made of the L2 header (18B) + MTU (1500B max by default). According to Cisco, a Giant baby FRAME can be up to 1600B big. So the MTU must be less or equal to 1582 (1600-18) and bigger than 1500. So, only 1518 fits in this case.

What do you think?

I passed this week after about 3 weeks of studying. Lots of questions were not covered here (the dumps really don’t cover ipv6 questions but they weren’t incredibly hard. CBTnuggets saved me giving lots of background and practical lab work (I just used GNS3 for the labs). I thought the labs were the easiest part.

@shadows
About
Which command can you enter to verify that a 128-bit address is live and responding?
A. traceroute
B. telnet
C. ping
D. ping ipv6
Answer: If you pinging from one cisco to another cisco it is ping ipv6. But if you ping from inside a host to a cisco its ping only.

@shadows
remember that if you pinging from 2 different networks, the hosts or cisco box need to have a valid global address like 2003. If its link local as fe80 it will only ping host inside the same network.

@CISCOTTE
You are welcome!
Btw, I just remember there was a question about how ipv6 is calculated. I mean EUI-64.
Answer: It uses Prefix and MAC …do some research to understand that.

i have some new brain dumbs how cann i share here with you people ?

@Me, I agree with you, Max MTU size is 1500 bytes and anything over 1500 will cause Baby giant Error. Those who say that it is 1600 and are referring to CISCO documentation, if you read the complete documentation, it says that some cisco devices can support MTU size up to 1600 bytes. Anyways i am not an expert, it is just my own understanding and no offense.

@Pl413r, Many thanks for your support, please continue to share if you remember any other question. Did you get any question on below ??

IOS License
Router BOOT up
IPV6 Prefix

Took my CCNA today. Ppap 130q are still valid. Simulations for Ospf, Acl, DHCP are same. If you’ve prepared for these dumps, you’ll get a min of 900. Good luck.

@Pl413r, Apart from the earlier question that i asked you, do you remember if you got this question in exam by any chance ??

Which name describes an IPV6 host-enable tunneling technique that uses IPV4 UDP,does not require dedicated gateway tunnels,and can pass through existing IPV4 NAT gateways?
A. dual stack
B. dynamic
C. Teredo
D. Manual 6to4

@ Shadows that would be C. Teredo.

In computer networking, Teredo is a transition technology that gives full IPv6 connectivity for IPv6-capable hosts that are on the IPv4 Internet but have no native connection to an IPv6 network. Unlike similar protocols, it can perform its function even from behind network address translation (NAT) devices such as home routers

Have ICND101-105 Exam Dec.15, wondering what the best dumps on these comment pages are for pass?

Where can i find the ppap 130q? Plz help!

@bgp_next_hop
I took the test twice and didn’t get a single one of those questions.

@Ciscocert
What are you talking about? I do know for a fact that if you only study what is on here you will not pass. Luckily I learned the material.

@ciscocert: Where can i find the ppap 130q?

@shadows
Yes I had this one…I chose dual stack
Apart from the earlier question that i asked you, do you remember if you got this question in exam by any chance ??

Which name describes an IPV6 host-enable tunneling technique that uses IPV4 UDP,does not require dedicated gateway tunnels,and can pass through existing IPV4 NAT gateways?
A. dual stack XX
B. dynamic
C. Teredo
D. Manual 6to4

About router bootup
After the power-on-self test (POST), the system LED of a Cisco 2950 switch turns amber. What is the status of the switch?
A. The POST was successful.
B. The switch has a problem with the internal power supply and needs an external power supply to be attached.
C. POST failed and there is a problem that prevents the operating system from being loaded. XX
D. The switch has experienced an internal problem but data can still be forwarded at a slower rate.
E. The switch passed POST, but all the switch ports are busy.

@shadows
About IPV6
Had one that asked what is used to build a ipv6 link local when auto config is enabled.
You need to know EUI-64

@PL413r

Hi Lucky #1lol! HAPPY THANKSGIVING to YOU!!!!

Which name describes an IPV6 host-enable tunneling technique that uses IPV4 UDP,does not require dedicated gateway tunnels,and can pass through existing IPV4 NAT gateways?
A. dual stack XX
B. dynamic
C. Teredo <<<<<<<?
D. Manual 6to4

In computer networking, Teredo is a transition technology that gives full IPv6 connectivity for IPv6-capable hosts that are on the IPv4 Internet but have no native connection to an IPv6 network. Unlike similar protocols, it can perform its function even from behind network address translation (NAT) devices such as home routers

YOU/WE need to know EUI-64
https://networklessons.com/ipv6/ipv6-eui-64-explained/
EUI-64 (Extended Unique Identifier) is a method we can use to automatically configure IPv6 host addresses. An IPv6 device will use the MAC address of its interface to generate a unique 64-bit interface ID. However, a MAC address is 48 bit and the interface ID is 64 bit. What are we going to do with the missing bits?

@PL413r

http://ipv6.com/articles/gateways/IPv6-Tunnelling.htm

Teredo, another IPv6 transition technology that provides address assignment and host-to-host automatic tunneling for unicast IPv6 traffic when IPv6/IPv4 hosts are located behind one or multiple IPv4 network address translators (NATs). To traverse IPv4 NATs, IPv6 packets are sent as IPv4-based User Datagram Protocol (UDP) messages. IPv6 traffic from Teredo hosts can flow across NATs because it is sent as an IPv4 UDP message. Note that The main benefit of Teredo is that its a NAT traversal technology for IPv6 traffic. If the NAT supports UDP port translation, then the NAT supports Teredo.

ciscotte are you there i have some new dombs but i dond know how to share her dumbs from last question

you need to split mac address in half and ad FFFE in the midle !!! and you need to invert 7-bits from mac address !! if 7 bits was 1 you need to invert it in 0 and via verse

@Starter

The best will be to put it on Google Drive!!!! OR > https://www.share.com/

i dont know how to do that if you give me your mail gonna send it to you then you cann share for others here !!! i have them in pdf format

@CISCOTTE
About…You might be right my question was diferent than this one…After reading it carefully i think I got it wrong! Happy Thanksgiving to you too!
Which name describes an IPV6 host-enable tunneling technique that uses IPV4 UDP,does not require dedicated gateway tunnels,and can pass through existing IPV4 NAT gateways?
A. dual stack
B. dynamic
C. Teredo <<<<<<<?
D. Manual 6to4

CISCOTTE
You can do hosto to host tunneling using 6to4 as well!

Starter is right about EUI-64

Anyone got ICND2 studying video? I am broke and need to study!

I meant
If anyone got ICND2 V3 studying videos (like CBT) and would like o share I would appreciate it, thank you!

@PL413r

Thanks PL, I’m wrong? So in 4the TEST what is the best Answer? Teredo?

Does anyone have the ppap dump and may you share it?
Or can you share the most recent valid dump ?

@CISCOTTE
Ye, I think you are right! I havent learned that teredo tunneling on ICND1.
After a quick google search “host-enable tunneling technique that uses IPV4 UDP” Teredo seems to be the correct answer.

@PL413r

Thanks PL….Talk 2U SOON!!! ARE YOU > @Rafael (PL413r) October 13th, 2016 P.4

@PL413r, this is not fair, CISCO is asking questions that are beyond course scope.

@CISCOTTE
No that’s a clone of me!
@shadows
Prepare for the worst bro, Study hard doing labs too, labs were the hardest I had at the exam. The rest was a peace of cake. I took long time on first lab untill I figured out that it was easier to read the answers and check if they were right in running-config (I consider this a VALUABLE source of info given to you guys)

@CISCOTTE & shadows
I just remember…had like few times (and wasnt sure what that mean at first) watch for that!
#line vty 0 4
password
no login ! It means that people can telnet into router with no password DANGEROUS
transport input telnet

@Pl413r, Thanks a lot, i am giving test tom and lets see how it goes….Did you get that VERU FAMOUS Baby Giant question by any chance hahahahaha. I will also call it out of course lolzzz

@shadows
No, thank god….no baby giant, no cef and no 6to4 crap.
One interest thing i read before exam starts was that…cisco said they could put questions that dont worth anything only for “testing purposes or analises or something” so those could be it!

@Pl413r
that’s interesting, i think these questions fall into those categories.
Did you make any notes on the lamination paper to help you in subnetting OR you nailed it in your brain.

@shadows
Yes took notes, but I dont need much space to subnet cause I have a ninja mode subnetting lol.
Btw make sure you get 2 pens…the a/c dries them out when you leave them open 🙂
ig2g night all!

@Pl413r,
ok sure, i will ask for 2 pens. Looking back, any other advise before the D-Day will be appreciated.

@PL413r

….So PL because you got EXTRA mn/ESL…..so that mean it took you like for NO ESL/90mn.
Other wise you ” just ” finish on time ( if you DIDN’T have extra time)!? PRESSURE ON!!!!!

@PL413r

Thanks again for the UPDATE PL!!!!

I just failed for the CCNA exam..grrrrrrrr 813 points:

The following question i had and see here a lot;

Which VLANs are system reserverd.

0 and 4095

http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/12-2SX/configuration/guide/book/vlans.html

NOT 0 and 1

Q What happes when you Disable CEF

a IP redirecting not working
b ACL logging not working

Etc

I do not know that answer

Thanks for that Dimie !!! i dont know why people is posting ansfers if they are not sure aboute that !!!you gonna make it next time you know what to espect next time you go to exam (:

@Dimie
It sounds like you blaming people here because you failed it.
Instead of doing that you should thank people here who posted the many other correct questions the helped you to get that close passing score!

i finf some new dumbs from november 21 hoppe this gonna help ya all pass the test !!! (:

https://drive.google.com/file/d/0B0HlD-X-g-ocdHp2b1JLejFxREE/view?usp=sharing

i have one good site where you cann learn for icnd 2 but it wonnt let me post here its something for you PL413r

@PL413r

Morning PL!! RIGHT!! Helping one to the other is what the Forum is about!!!!
Everything will be alright!!!! Lets go POSITIVE!!!! FAILLING IS NOT AN OPTION!!!!

@PL413r

YOUUR OPINION about >
Q. Which VLANs are system reserverd.
0 and 4095 ( NOT 0 and 1 )

http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/12-2SX/configuration/guide/book/vlans.html

@ALL ALL ALL

Starter is FISHING!!!!! I DON’T KNOW WHAT IS UP TOO????

What do you mean fishing ????

@Starter
Why ask permission?

@All
When you get this type of request, dont enter any email account that could identify yourself

@CISCOTTE

YOUUR OPINION about >
Q. Which VLANs are system reserverd.
0 and 4095 ( NOT 0 and 1 )

Answer: If its on the cisco page/book 0 and 4095 than that is the correct one! This answer makes sense because vlan 1 can be modified to whatever you want and vlan 0 can not.

@PL413r

TRY THIS:

s-p-a-c-e-s-.-h-i-g-h-t-a-i-l-.-c-o-m-/-s-p-a-c-e-/-5-c-e-U-l

(just remove the “-“)