Share your ICND1 v3.0 Experience

ICND1

Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true?
A. IP routing must be enabled to allow the two hosts to communicate.
B. The two hosts are in the same broadcast domain.
C. The switch must be configured with a VLAN to allow the two hosts to communicate.
D. Port security prevents the hosts from connecting to the switch.

Answer = why A why not B ?

Please correct me if anything is wrong.

1: Which MTU size can cause a baby giant error?
A. 1500
B. 9216
C. 1600
D. 1518

correct ans : D or C ?

2: Which statement about native VLAN traffic is true?

A. Cisco Discovery Protocol traffic travels on the native VLAN by default.
B. Traffic on the native VLAN is tagged with 1 by default.
C. Control plane traffic is blocked on the native VLAN.
D. The native VLAN is typically disabled for security reasons.

answer: ?

3: Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true?
A. IP routing must be enabled to allow the two hosts to communicate.
B. The two hosts are in the same broadcast domain. < ( ANS )
C. The switch must be configured with a VLAN to allow the two hosts to communicate.
D. Port security prevents the hosts from connectingto the switch.

4: Which option is a valid hostname for a switch?
A. Switch-Cisco
B. Switch-Cisco!
C. SwitchCisco < ( ANS )
D. SwitchCisc0

5: Which two characteristics describe the access layer of the hierarchical network desing model?
A. layer 3 support
B. port security < ( ANS )
C. redundant components
D. VLANs < ( ANS )
E. PoE

6: Under which circumstance should a network administrator implement one-way NAT?
A. when the network must route UDP traffic
B. when traffic that originates outside the network must be routed to internal hosts
C. when traffic that originates inside the network must be routed to internal hosts
D. when the network has few public IP addresses and many private IP addresses require outside access < ( ANS )

7: After the power-on-self test (POST), the system LED of a Cisco 2950 switch turns amber. What is the status of the switch?
A. The POST was successful.
B. The switch has a problem with the internal power supply and needs an external power supply to be attached.
C. POST failed and there is a problem that prevents the operating system from being loaded. < ( ANS C )
D. The switch has experienced an internal problem but data can still be forwarded at a slower rate.
E. The switch passed POST, but all the switch ports are busy.

8: Which RFC was created to alleviate the depletion of IPv4 public addresses?
A. RFC 4193
B. RFC 1519
C. RFC 1518
D. RFC 1918 < ( ANS )

9: Which value is indicated by the next hop in a routing table?
A. preference of the route source
B. IP address of the remote router for forwarding the packets < ( ANS )
C. how the route was learned
D. exit interface IP address for forwarding the packets

10: Which entity assigns IPv6 addresses to end users?
A. ICANN
B. APNIC
C. RIR
D. ISPs < (ANS)

11 :Which statement about routing protocols is true?
A. Link state routing protocols choose a path by the number of hops to the destination. < ( ANS )
B. OSPF is a link state routing protocol.
C. Distance vector routing protocols use the Shortest Path First algorithm.
D. ISIS is a distance vector routing protocol.

12: Which MTU size cause a baby giant error? (1518)
13: which RFC was created to alleviate the depletion of IPVA4 pulic adresse? (RFC 1918 )
14: which entity assigns IPV6 addresse to end user? (ISPs )

15- Which technology allows a large number of private IP addresses to be represented by a smaller number of public IP addresses? (NAT Overload)
16- Which NTP command configures the local device as an NTP reference clock source? (NTP)
second one i choose NTP master ?
17- Which device allows users to connect to the network using a single or double radio? (Access Point)

18- One question of eigrp but very easy (“AD eigrp 90”)

Going for My ICND1 this coming wednesday. Please help!

Jean Claude Van Damme

September 23rd, 2016

There is only one book. Can you give the link of the other book?

I would like to share the 2 books, if anyone is interested.

https://drive.google.com/open?id=0B6mnbxOlbXoxVlk1RGVtemZ0dU0

https://drive.google.com/open?id=0B6mnbxOlbXoxWnZtZTl6bzBnNVU

Try @geo regards

Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true?
A. IP routing must be enabled to allow the two hosts to communicate.
B. The two hosts are in the same broadcast domain.
C. The switch must be configured with a VLAN to allow the two hosts to communicate.
D. Port security prevents the hosts from connecting to the switch.

Answer: A

1: Which MTU size can cause a baby giant error?
A. 1500
B. 9216
C. 1600
D. 1518
correct ans : C

2: Which statement about native VLAN traffic is true?
A. Cisco Discovery Protocol traffic travels on the native VLAN by default.
B. Traffic on the native VLAN is tagged with 1 by default.
C. Control plane traffic is blocked on the native VLAN.
D. The native VLAN is typically disabled for security reasons.
answer: A

3: Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true?
A. IP routing must be enabled to allow the two hosts to communicate.
B. The two hosts are in the same broadcast domain.
C. The switch must be configured with a VLAN to allow the two hosts to communicate.
D. Port security prevents the hosts from connectingto the switch.

Answer: A

4: Which option is a valid hostname for a switch?
A. Switch-Cisco
B. Switch-Cisco!
C. SwitchCisco < ( ANS )
D. SwitchCisc0

5: Which two characteristics describe the access layer of the hierarchical network desing model?
A. layer 3 support
B. port security < ( ANS )
C. redundant components
D. VLANs < ( ANS )
E. PoE

6: Under which circumstance should a network administrator implement one-way NAT?
A. when the network must route UDP traffic
B. when traffic that originates outside the network must be routed to internal hosts <= Ans
C. when traffic that originates inside the network must be routed to internal hosts
D. when the network has few public IP addresses and many private IP addresses require outside access

8: Which RFC was created to alleviate the depletion of IPv4 public addresses?
A. RFC 4193
B. RFC 1519
C. RFC 1518
D. RFC 1918 < ( ANS )

9: Which value is indicated by the next hop in a routing table?
A. preference of the route source
B. IP address of the remote router for forwarding the packets < ( ANS )
C. how the route was learned
D. exit interface IP address for forwarding the packets

10: Which entity assigns IPv6 addresses to end users?
A. ICANN
B. APNIC
C. RIR
D. ISPs < (ANS)

11 :Which statement about routing protocols is true?
A. Link state routing protocols choose a path by the number of hops to the destination. < ( ANS )
B. OSPF is a link state routing protocol.
C. Distance vector routing protocols use the Shortest Path First algorithm.
D. ISIS is a distance vector routing protocol.

@ICND1
Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true?
A. IP routing must be enabled to allow the two hosts to communicate.
B. The two hosts are in the same broadcast domain.
C. The switch must be configured with a VLAN to allow the two hosts to communicate.
D. Port security prevents the hosts from connecting to the switch.
Correct:B
Explanation: switch are layer 2 OSI and dont do routing, no need to configure VLAN to comunicate, all switches come with native VLAN 1 preconfigured, default switch configuration dont come with port security

@ICND1
unless you create a new VLAN all ports are in same broadcast domain, that’s why correct is B.

@ICND1
You have some wrong answers there my friend.
As far as i know
1-?
2-B
3-B
4-C
5-B D
6-?
8-C
9-B
10-C
11-?

guys, share the dumps … VCE or PDFs

Any resource because I found another website they chose the 1st option but how?

@TECH
1-D
2-B
3-B and A still I’m confused but i saw A and also B
4-c
5-B AND E
6-B
7-C
8-D
9-B
10-D
11-A
12-1518
13- RFC1918
14-ISP
15-NAT OVERLOAD
16- NTP Master

Guys try this site, they have 100-105 practice questions

http://www.learncisco.net/test-ccna.php?exam=100-105

Guys, I need your opinion. As I am preparing for an exam and I downloaded basically all free exams, which I have found on the internet and went through all of them, basically got familiar with them and then I did practical exam on learncisco . net and that test seems to me like 3 times harder, than all other test I did before. What do you think, are the ICND1 so difficult than are test on this page? Thx for answer in advance

@black box this is true, it seems at learncisco.net question are difficult.

And somebody who took ICND1 – the exam itself is more learncisco.net or 9tut.net?

Hi friends, I take the exam yesterday, I PASS!!!! and as I passed the ICND2 200-101, I am CCNA.
I will tell you my experience ICND 100-105:

I practiced with passleader (it has much errors), although it is true that all questions were here
I recommend you consider this if they have one, but do not rely on responses only 80% are correct.

the famous labs DHCP:
is very easy, it has ACL, DHCP, NTP and NAT, the question are basic (it
asks no configuration), you aplicate show running-config and verificate the configuration,
-I was wrong last time with NAT (the Access List is applied to the interface loop 127.0.0.1), why would not allow traffic is the correct answer.
-the access list block the traffic for the host, only analyze int he R1 and the answer is very easy.
-NTP is not configured in the R2 is why they do not receive updates.
– once again,SHOW RUNNING-CONFIG it is the solution to this LAB

the second LABs were the Security Testlet.
-again simple, you must clearly have concepts in VTY password, SSH, configuration of privilegies,user and “passwords 0-7”, also our ally show running-config, oh hell, I love this command, :).

finally this question is wrong:

4: Which option is a valid hostname for a switch?
A. Switch-Cisco
B. Switch-Cisco!
C. SwitchCisco
D. SwitchCisc0

real options in the test:
A. 5witch-Cisco
B. Switch-Cisco!
C. 5witchCisco
D. SwitchCisc0

1: Which MTU size can cause a baby giant error?
A. 1500
B. 9216
C. 1600
D. 1518
correct ans : B!

normal MTU Is 1500 for an Ethernet frame. Baby giant supports up to 1600 that means it can support A,C,D. Jumbo supports up to 9216, but the question is not asking about jumbo

Also you guys just throw answers up like we are playing darts, here is my answer sheet:

Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true?
A. IP routing must be enabled to allow the two hosts to communicate.
B. The two hosts are in the same broadcast domain.
C. The switch must be configured with a VLAN to allow the two hosts to communicate.
D. Port security prevents the hosts from connecting to the switch.

Answer: B – By default (in a default configuration) port security is not enabled, all ports are assigned vlan 1 and switch is layer two so there is no routing. Because all ports are in VLAN 1 there is no need to route, and they are in the same broadcast domain. Now if they were in different vlans then yes, you would need a router because switches cannot route between vlans

1: Which MTU size can cause a baby giant error?
A. 1500
B. 9216
C. 1600
D. 1518
correct ans : B- As stated in the post above

2: Which statement about native VLAN traffic is true?
A. Cisco Discovery Protocol traffic travels on the native VLAN by default.
B. Traffic on the native VLAN is tagged with 1 by default.
C. Control plane traffic is blocked on the native VLAN.
D. The native VLAN is typically disabled for security reasons.
answer: B – Trivial.

4: Which option is a valid hostname for a switch?
A. Switch-Cisco
B. Switch-Cisco!
C. SwitchCisco
D. SwitchCisc0

ans – ? – If anyone can provide documentation on this it would be helpful

5: Which two characteristics describe the access layer of the hierarchical network design model?
A. layer 3 support
B. port security
C. redundant components
D. VLANs
E. PoE

Ans – B,D.

A typical hierarchical topology is.
•A core layer of high-end routers and switches that are optimized for availability and performance.
•A distribution layer of routers and switches that implement policies.
•An access layer that connects users via lower-end switches and wireless access points.

6: Under which circumstance should a network administrator implement one-way NAT?
A. when the network must route UDP traffic
B. when traffic that originates outside the network must be routed to internal hosts
C. when traffic that originates inside the network must be routed to internal hosts
D. when the network has few public IP addresses and many private IP addresses require outside access

ans – D one-way nat is pat and pat’s definition is D

8: Which RFC was created to alleviate the depletion of IPv4 public addresses?
A. RFC 4193
B. RFC 1519
C. RFC 1518
D. RFC 1918

ans – D – trivial

9: Which value is indicated by the next hop in a routing table?
A. preference of the route source
B. IP address of the remote router for forwarding the packets
C. how the route was learned
D. exit interface IP address for forwarding the packets

ans – B – packets are sent from a router to the ip address of a “next-hop router” for forwarding the packet

10: Which entity assigns IPv6 addresses to end users?
A. ICANN
B. APNIC
C. RIR
D. ISPs

ans – D

11 :Which statement about routing protocols is true?
A. Link state routing protocols choose a p by the number of hops to the destination.
B. OSPF is a link state routing protocol
C. Distance vector routing protocols use the Shortest Path First algorithm.
D. ISIS is a distance vector routing protocol

ans – B – OSPF, ISIS is a link state protocol. RIP is a distance vector protocol.

But baby giant can support up to 1600? Isnt that inclusive?

The question says what would create an error, answers 1600 and below would not

do ICND1 cover baby giant? i couldn’t find it anywhere in the book

@dood
11 :Which statement about routing protocols is true?
A. Link state routing protocols choose a p by the number of hops to the destination.
B. OSPF is a link state routing protocol
C. Distance vector routing protocols use the Shortest Path First algorithm.
D. ISIS is a distance vector routing protocol
ans – B – OSPF, ISIS is a link state protocol. RIP is a distance vector protocol.
black box September 30th, 2016

in real exam i chose 2th option but people in this community and somewhere else said the A is correct
?

@pass B is correct.

RIP == number of hops
OSPF == link state
RIP != OSPF
so A == false

About question 4 above, I think the question has to change to
4: Which option is a INVALID hostname for a switch?
A. Switch-Cisco
B. Switch-Cisco!
C. SwitchCisco
D. SwitchCisc0

ans: B

taking the test in 2 days. Can anyone post a current dump please?

Nick – I totally agree, first character is alphabetic, last character is alphanumeric, and can have alphanumeric letters in the middle and hyphens. So in our case, B is the right answer

pass – quick research will show you the ospf is a link state routing protocol, but it is not choosen by the number of “hops”. Distance vector protocals are choosen by the number of hops, like RIPv2. In our case OSPF is a link state protocol that uses BANDWITH and calculates PATH COST. And ISIS is a linked state not distance vector. I hope that clears some things up

Also, The answer I put for baby giant was my educated guess. It is not in the book, but many people have received the question. I think it is 9216 because baby giant can support MTU frames 1600 and BELOW. jumbo frames can support 9216 and BELOW. So the question is asking about a baby giant ERROR. There would be an error at size 9216 because that’s jumbo, and the question clearly states baby giant.

If anyone else would like to chime in and state there opinions and justifications, that would be nice too

Gave ICND1 today and passed .
There were 3 questions based on IPv6 Auto Configuration.
Security, DHCP, NAT and ACL labs
baby giant error – 1516
IPv4 depletion – RFC1918
default DHCP lease time

Good Luck!

Which exam did you take @ICND1 v.3, there is no 1516

Took this one a few days ago. Look for this free dump on google, all 35 of those questions were in my test.

Cisco.Prep4sure.100-105.v2016-07-07.by.Greg.35q.pdf

Hi 37!

PLEASE:

1) I CAN’T FIND the link ( for FREE of CHARGE ) this file
Cisco.Prep4sure.100-105.v2016-07-07.by.Greg.35q.pdf

2) since you took the 100-105 few day ago ( assuming you PASS > CONGRADULATION!!!! ), But concerning the ” LAB ”
a) how many? < SIM?, SIMLET?
b) config or NO config
c) since 9Tut has NO SIM for 100-105 – do you any tip where to practice on it??

3) I'm looking for VCE who won't charge me $55.99 for a MONTH!!!

Any tip will be sincerely appreciated,
Thank you and again, CONGRAT!!!

“If a lease is not specified for an IP address, by default, the DHCP Server assigns a one-day lease for the address.”

[reference: http://www.cisco.com/c/en/us/td/docs/ios/12_2/ip/configuration/guide/fipr_c/1cfdhcp.html, also 100-101 book page 220, example 8-11 where a lease of 86400 seconds is showed ~ 1day]

justchecked#2
10: Which entity assigns IPv6 addresses to end users?
A. ICANN
B. APNIC
C. RIR
D. ISPs

100-101 book, page 717, IANA gives addresses to RIRs, RIRs to ISPs and ISPs to Companies (end users)…

So, the answer is D.

lastly,

“Standard Ethernet frame MTU is 1500 bytes. This does not include the Ethernet header and Cyclic Redundancy Check (CRC) trailer, which is 18 bytes in length, to make the total Ethernet frame size of 1518. In this document, MTU size or packet size refers only to Ethernet payload. Ethernet frame size refers to the whole Ethernet frame, including the header and the trailer. Baby giant frames refer to Ethernet frame size up to 1600 bytes, and jumbo frame refers to Ethernet frame size up to 9216 bytes.” [reference: http://www.cisco.com/c/en/us/support/docs/switches/catalyst-4000-series-switches/29805-175.html ]

Based on this, my answer to question would be C – 1600
1: Which MTU size can cause a baby giant error?
A. 1500
B. 9216
C. 1600
D. 1518

hello

is it advisable to write the composite exams or should i just write them separate?

ICND1
you find the DHCP // true i pass with this where can have the .pdf ?

@CISCOTTE, Thanks, I passed with 980/1000.

1) Look for a website called gratis exam (no space). It is (was?) filtered on 9tut, otherwise I’d have posted the link. Otherwise, look for “Which MTU size can cause a baby giant error” (with quotation marks), that also gets you to valid dumps. I had that question on my test.

2) 1 sim with DHCP (wrong+missing statement configured), an ACL which was blocking traffic and a NAT pool with wrong IP addresses.
1 simlet with basic security questions on a router and switch about telnet / ssh, it had inappropriate login messages (can’t “welcome” hackers into your device)

3) The questions were all very easy, I prepared way too hard for this test. Good luck on your studies.

Also, no config required. show commands only.

I wish someone can just clearly say what the answer is to this baby giant problem. the answer 1518 makes no sense to me since baby giant supports mtu up to 1600

i think you should all leave this BABY GIANT questions alone & focus on other important stuff.

true

@37, so can you confirm if the Greg.35q.pdf question dumps is valid for the 100-105 exam?

Yes, ALL of those 35 questions were on my test. No exception.

Thanks you ” 37 ” on my way to find this file!!!?

h t t p : / / w w w . g r a t i s e x a m . c o m / all question from this website but be careful some answer are wrong
Security Testate find any good website don’t use 9tut for this question
ICND September 24th, 2016

IN FACT ” 37 ” – IN FACT I have had the file in my download folder!!!!

My issue is that my VCE Player won’t play it (only if I upgrade it for $55.99 ) they said is new VCE version!!!!

So if you have a link for the “.pdf ” version I will really appreciate!?

I’m Googling it for it, right now!!!

Thanks again!

@Ricce21
Please share your passleader docs please!
Thank you all for helping. I am taking my icnd1 soon.

Greg.35q.pdf below link
h t t p : / / g r a t i s e x a m s . c o m / c i s c o / 1 0 0 – 1 0 5 /

Jean Claude Van Damme
You are a legend mate ~

Hi everyone

Guys please please share the valid PassLeader dumps

##########################################################################

Passleader dumps

please

##########################################################################

I will confirm for you all, taking the exam in the next wk or so. Stay tuned.

Taking it tomorrow, I will update this thread

are the quiz questions the same as the real test? plz answer

Just know the material, the questions and answer documents are a bonus

hi RICCE21 can you share the passleader dump 100-105? thank you sir

waltercorona60 gmail.com

thankyou sir

passleader is garbage, and I’m pretty sure they automate posts on 9tut to get you to buy it

Guys,

Get INE video, it is comprehensive. All the topic is covered, ISP dish out IPV6, RFC 1918,OSPF link state,subnetting etc

All of the questions in that PDF are correct and on the exam.

@Joe Mama which PDF?

Dood how did it go?

Dodo please take us out of this misery ; (

Hi all, can i ask your guys to share the labs or simlet that were in the exam?

how’s going Dood?

PL413r
check two step back and you could find all simulate

Taking it in 2 hours

Hello Guys. I f&&Ked it up differently. The exam was so hard like it cannot be explained in words. That is i can say atm…

noooooooooooooooooooooooooooo

Congrats Bro.

@dood what kind of simulations & testlets did you get??

p.s can you please provide the link of those dumps again. cheers 😀

@dood
Brother, what did you answer in that baby giant one?
@LFC
h t t p : / / g r a t i s e x a m . c o m / c i s c o / 1 0 0 – 1 0 5 – e x a m /

@Pl413r this link has icnd2 questions?? what’s the story?

@LFC
no man, its for exam 100-105 (ICND1)

Hey guys! Doing the exam in a few weeks. Has anyone tried the exambible 100-105 dumps?

Hello

this is the updated DHCP and RIPv2. with complete running configs.
https://drive.google.com/open?id=0B9XjqInn_2WiWFpNeG83M3AtdDg
password is pineapple.

@ICND1
Is this the actual ICND1 SIM?

It is the same topology but the questions and answers are a bit different

but same conceptual questions. Also the baby giant I put 1518 as that is what it was in gratis exams

@dood
Brother, what did you answer in that baby giant one? Is there a way to know if your answer correct?

I don’t know if it was correct, I just put what gratis exams had

Ok thanks.

@Door

ACL and NAT asked in exam or not?

Thank you

almost same @dood and @Pl413r

777/1000 / 54 questions / 832 is passing marks

ICND1 you the man . I failed it but i am happy everything i studies was right. only few things were bit confusing as you said.
simulations are the same as ICND1 is sharing.
something about control shift 6x on a telnet session what does the resume command then do

RFC 1918 for Internet Protocol Version 4 (IPv4)
RFC 4193 for Internet Protocol Version 6 (IPv6)

both are in the exam.
Baby S*** is pain.

Can someone reply with the correct answer i selected 1600 in test

i

Is there a way i can find how many questions i did wrong my marks are 777/1000.

Thank you

Sorry TECH i dont think theres a way to know…I am talking with a CCIE for trying simulating this baby giant frame size error. I the mean time if you know someone else who might know the right answer please let us know.

Failed with a score of 813, is a shame I felt pretty good with my answers, I’m pretty sure I answered the lab questions correctly. I still remember all my questions and answers, going to make a list and compare with answers posted here.

@ICND1
do you mind it letting me download the .pdf from google drive?

@Qwerty
Please share the questions you remember with us.

Got 918/1000 this morning 🙂

many question from the 35q gratis pdf.

About the baby giant, my answer was 1518 as in gratis pdf, but for what i studied, the answer could be 9126. baby giant is supported up to 1600, so to cause error, it must be over 1600

@Tech @Nick @Qwerty

Please can you share more details for this exam?

Thank you.

1)Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true?
A. IP routing must be enabled to allow the two hosts to communicate.
B. The two hosts are in the same broadcast domain.
C. The switch must be configured with a VLAN to allow the two hosts to communicate.
D. Port security prevents the hosts from connecting to the switch.

Answer:

2)Which MTU size can cause a baby giant error?
A. 1500
B. 9216
C. 1600
D. 1518

Answer:

3)Which option is a valid hostname for a switch?
A. 5witch-Cisco
B. Switch-Cisco!
C. 5witchCisc0
D. SwitchCisc0

Answer:

4)Which statement about native VLAN traffic is true?
A. Cisco Discovery Protocol traffic travels on the native VLAN by default.
B. Traffic on the native VLAN is tagged with 1 by default.
C. Control plane traffic is blocked on the native VLAN.
D. The native VLAN is typically disabled for security reasons.

Answer:

5)Under which circumstance should a network administrator implement one-way NAT?
A. when the network must route UDP traffic
B. when traffic that originates outside the network must be routed to internal hosts
C. when traffic that originates inside the network must be routed to internal hosts
D. when the network has few public IP addresses and many private IP addresses require outside access

Answer:

6)Which statement about routing protocols is true?
A. Link state routing protocols choose a path by the number of hops to the destination.
B. OSPF is a link state routing protocol.
C. Distance vector routing protocols use the Shortest Path First algorithm.
D. ISIS is a distance vector routing protocol.

Answer:

Thank you.

1) A
2) C
3) D
4) A
5) D
6) B

Answer are right or wrong?

https://supportforums.cisco.com
we can ask to professional people here.

@Pl413r i copied and pasted your link & i clicked on the first one which is PDF File and exam it has is for icnd2 not for icnd1. please make it clear.

^exam code

1-B
2-?
3-D
4-A
5-?
6-B

@LFC
Take out the spaces man
If you are studying for ICND1 you should know that you need exam 100-105
You are welcome!
h t t p : / / g r a t i s e x a m . c o m / v c e – t o – p d f / c i s c o / 1 0 0 – 1 0 5 / C i s c o . P r e p 4 s u r e . 1 0 0 – 1 0 5 . v 2 0 1 6 – 0 7 – 0 7 . b y . G r e g . 3 5 q . p d f /