Share your ICND1 v3.0 Experience

Thanks Wayne!!!!

Quick Question (exam in two hours) I see this question is different in all of the dumps. Which one is correct?

Which values is indicated by the next hop in a routing table?

How the route was learned?
Preference of the route source?
IP address of the remote router for forwarding the packets?<—some say this
Exit Interface IP address for forwarding packets?<—other say this

IP address of the remote router for forwarding the packets?<—some say this

@wayne ..It exit interface

For your reference….

7.) Which device allows users to connect to the network using a single or double radio? (Answer Access Point)

8.) Which statement about routing protocols is true?
A.
Link state routing protocols choose a path by the number of hops to the destination.
B.
OSPF is a link state routing protocol.
C.
Distance vector routing protocols use the Shortest Path
First algorithm.
D.ISIS is a distance vector routing protocol.

9.) Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true?
A. IP routing must be enabled to allow the two hosts to communicate.
B. The two hosts are in the same broadcast domain.
C. The switch must be configured with a VLAN to allow the two hosts to communicate.
D. Port security prevents the hosts from connecting to the switch.
Which statement about native VLAN traffic is true?

10.) Which option is a valid hostname for a switch?
A. Switch-Cisco
B. Switch-Cisco!
C. SwitchCisco
D. SwitchCisc0

11.) Which two characteristics describe the access layer of the hierarchical network design model?
A. layer 3 support
B. port security
C. redundant components
D. VLANs
E. PoE

12.) Under which circumstance should a network administrator implement one-way NAT?
A. when the network must route UDP traffic
B. when traffic that originates outside the network must be routed to internal hosts
C. when traffic that originates inside the network must be routed to internal hosts
D. when the network has few public IP addresses and many private IP addresses require
outside access

13.) After the power-on-self test (POST), the system LED of a Cisco 2950 switch turns amber. What is the status of the switch?
A. The POST was successful.
B. The switch has a problem with the internal power supply and needs an external power supply to be attached.
C. POST failed and there is a problem that prevents the operating system from being loaded.
D. The switch has experienced an internal problem but data can still be forwarded at a slower rate.
E. The switch passed POST, but all the switch ports are busy.
Correct: C

14.) Which MTU size can cause a baby giant error?
A. 1500
B. 9216
C. 1600
D. 1518

15.) Which statement about native VLAN traffic is true?
A. Cisco Discovery Protocol traffic travels on the native VLAN by default.
B. Traffic on the native VLAN is tagged with 1 by default.
C. Control plane traffic is blocked on the native VLAN.
D. The native VLAN is typically disabled for security reasons.

16.) Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true?
A. IP routing must be enabled to allow the two hosts to communicate.
B. The two hosts are in the same broadcast domain.
C. The switch must be configured with a VLAN to allow the two hosts to communicate.
D. Port security prevents the hosts from connecting to the switch.

17.) Which option is a valid hostname for a switch?
A. Switch-Cisco
B. Switch-Cisco!
C. SwitchCisco
D. SwitchCisc0

18.) Which RFC was created to alleviate the depletion of IPv4 public addresses?
A. RFC 4193
B. RFC 1519
C. RFC 1518
D. RFC 1918

19.) Which value is indicated by the next hop in a routing table?
A. preference of the route source
B. IP address of the remote router for forwarding the packets
C. how the route was learned
D. exit interface IP address for forwarding the packets

20.) Which entity assigns IPv6 addresses to end users?
A. ICANN
B. APNIC
C. RIR
D. ISPs

21.) Which statement about routing protocols is true?
A. Link state routing protocols choose a path by the number of hops to the destination.
B. OSPF is a link state routing protocol.
C. Distance vector routing protocols use the Shortest Path First algorithm.
D. ISIS is a distance vector routing protocol.

22.) Which technology allows a large number of private IP addresses to be represented by a smaller number of public IP addresses?

23.) Which NTP command configures the local device as an NTP reference clock source? (NTP) second one i choose NTP master ?

24.) What is the administrative distance of EIGRP?

25.) Which statement about native VLAN traffic is true?
A. Cisco Discovery Protocol traffic travels on the native VLAN by default.
B. Traffic on the native VLAN is tagged with 1 by default.
C. Control plane traffic is blocked on the native VLAN.
D. The native VLAN is typically disabled for security reasons.
answer: A

26.) Which address type does a switch use to make selective forwarding decisions?
A. Source IP address
B. Destination IP address
C. Source and destination IP address
D. Source MAC address
E. Destination MAC address

27.) What must occur before a workstation can exchange HTTP packets with a web server?
A. A UDP connection must be established between the workstation and its default gateway.
B. A UDP connection must be established between the workstation and the web server.
C. A TCP connection must be established between the workstation and its default gateway.
D. A TCP connection must be established between the workstation and the web server.
E. An ICMP connection must be established between the workstation and its default gateway.
F. An ICMP connection must be established between the workstation and the web server.

28.) Which two of these functions do routers perform on packets? (Choose two.)
A. Examine the Layer 2 headers of inbound packets and use that information to determine the next hops for the packets
B. Update the Layer 2 headers of outbound packets with the MAC addresses of the next hops
C. Examine the Layer 3 headers of inbound packets and use that information to determine the next hops for the packets
D. Examine the Layer 3 headers of inbound packets and use that information to determine the complete paths along which the packets will be routed to their ultimate destinations
E. Update the Layer 3 headers of outbound packets so that the packets are properly directed to valid next hops
F. Update the Layer 3 headers of outbound packets so that the packets are properly directed to their ultimate destinations

29.) what does administrative distance refer to?
a) the cost of link between 2 neighboring routers
b) the advertised cost to reach a network
c) the cost to reach a network that is administratively safe
d) a measure of the trustworthiness of a routing information source

30.) Which two commands will display the current IP address and basic Layer 1 and 2 status of an interface?( Choose two)
A. router# show version
B. router# show ip interface
C. router# show protocols
D. router# show controllers
E. router# show running-config

Hi everyone, i can really use some advice from some professionals.

I just watched CBTNuggets videos and went through a CCENT 100-105 book, i dont feel too confident about taking the test yet. What should i study that will be on the test? I wanna actually learn the certification before i start using dumps which is why im asking!

NTP, RIPv2, DHCP, NAT, IPv4 Broadcast etc…., VLANs

Just go on the cisco site and look at the exam topics for 100-105. If you see something you’re not 100% on, study that.

Once you feel you know most topics take a practice quiz and note down anything you do not understand or that you get wrong.

You can then study these topics.

@Zayn forget the exam for now, keep studying from various sources. read everything you have read before watch the videos over and over again and most importantly look at some of these questions on here

@CISCOTE
Which two commands will display the current IP address and basic Layer 1 and 2 status of an interface?( Choose two)
A. router# show version (just wrong)
B. router# show ip interface X
C. router# show protocols (wrong command right is sh ip protocols)
D. router# show controllers X
E. router# show running-config (doesnt show l1)

@Wayne
Which values is indicated by the next hop in a routing table?
How the route was learned?
Preference of the route source? (wrong)
IP address of the remote router for forwarding the packets?(correct)
Exit Interface IP address for forwarding packets? (wrong because isnt ip …right is interface like s/0/0)

@Zayn
Use Dave’s SIMs/Quizes if you do well on that you will pass….

Okay,
thanks for the advice everyone!

Where I can see exams or questions to practice for the exam 200-125

@Dave do you recommend i use 9tut to study “NTP, RIPv2, DHCP, NAT, IPv4 Broadcast etc…., VLANs” ?

@Vince
Thanks!

@Wayne
The sim topolgie was the same than RIPv2_SIM_1, but there was a different running config and questions.

@Pl413r

No, It is not, was a different one.
The question in my exman there was just one correct answer. That should be 6to4, i guess.

So my test was 25% dumps and 75% topics not covered here. I passed btw.

@Cicote

show protocols and show ip interface are most certainly correct

Get Cisco PacketTracer (free) and run the commands to verify, don’t just take answers on this forum as gospel as there is definitely some incorrect answers being given. No offense to anyone..the bajillion show commands confuse us all. 🙂

@Wayne
Can you be more specific? What do you remember that was not covered here?

@Wayne
Congratulations!!!!!!

@PL413r I wont worry if I were you. I think I got enough reading, videos and practice questions to sail through

But forgot to add I hear Cisco is a monster. very scaryyyyy but we will be fine

Hello,
what is the best way to practice the labs from the exam? I got Dave’s dumps and there are +500 test questions, which is great. But what can of labs simulations can I expect in the exam? (are they like a packet tracer exercise that we need to complete before X minutes?)
Thanks!!!

Passed my 100-101 Exam, I would like to thanks http://pass4surekey.com/exam/100-101.html for updated and valid dumps.

Thanks@
1) PL413r – when are taking your TEST? You seams good to go?????
2) Wayne – CONGRAT
3) Tapout – I’m using PKT & I have to recheck myself on that one!

Still confuse on that one!!

Two hosts are attached to a switch with a default configuration. Which statement about the configuration is true?

A) IP routing must be enabled to allow the two hosts to communicate
B) The two hosts are in the same broadcast domain
C) The switch must be configured with a VLAN to allow the two hosts to communicate
D) Port security prevents the hosts from connecting to the switch

A or B is my option since they is only 1 switch & no VLAN – STILL can’t be 100% SURE

@Ciscotte Answer is B, by default both hosts will be in VLAN 1 which is a broadcast domain.

@Ciscotte, I hit submit too soon. By default, vlan 1 always exists

@CISCOTTE – That question is wrong on the dumps, I think. IP routing is the answer on the dumps and it doesn’t make sense to me. It has to be B since a router is the only device to break up broadcasts.

Two hosts are attached to a switch with a default configuration. Which statement about the configuration is true?

A) IP routing must be enabled to allow the two hosts to communicate
B) The two hosts are in the same broadcast domain <——- ANSWER
C) The switch must be configured with a VLAN to allow the two hosts to communicate
D) Port security prevents the hosts from connecting to the switch

@Noob $ TapOut – Thanks!

PL413r & Dave:In that question I would like to know WHAT would be your theory about it: A/B???I’m still confuse the way they are presenting the question??? To me it’s DOUBLE TALK!!
Thanks Guys!

Can anyone tell, we can go back and forth between questions OR do we have to answer them as they appear. I was wondering if i could skip the tough questions and come back on them later ??

@ciscotte

A switch does does not require ip routing for 2 hosts to communicate if they are in the same vlan. A L2 switch “switches” traffic via destination MAC, so A is wrong.

A vlan = a broadcast domain period. Meaning if an ethernet broadcast packet came in to a vlan, it would be sent out all ports within that vlan except the port it was received on.

Thanks TapOut – clear now!!

Standard Ethernet frame MTU is 1500 bytes. This does not include the Ethernet header and Cyclic
Redundancy Check (CRC) trailer, which is 18 bytes in length, to make the total Ethernet frame size
of 1518. In this document, MTU size or packet size refers only to Ethernet payload. Ethernet frame
size refers to the whole Ethernet frame, including the header and the trailer. Baby giant frames
refer to Ethernet frame size up to 1600 bytes, and jumbo frame refers to Ethernet frame size up to
9216 bytes.

1 ) Which MTU size can cause a baby giant error? > 1518
2 ) Which MTU size can cause a baby giant error? > 1600

So its 1518 correct ?

@kik been discussed many times, its 1600

@Zayn
but refer to the explanation. MTU is 1500 b; frame is 1518; so in the options is mtu size, if MTU is 1600 -> frame 1618 and it is a jumbo frame error ; right ? i want to be sure.
From Cisco documents :
Baby giants are supported, however they are counted as oversized giant packets.
The error counter is incremented in the output of the show interface command

Package Include:

ICND1 (100-105) = 239Qs and 201Qs
ICND2 (200-105) = 110Qs and 204Q
Latest Dumps in Both PDF & VCE Format.
Working VCE Player
All LABS TOPOLOGIES for Packet Tracer 6.0.1
You will also get free updates for 60 Days, starting from your contribution date.

FYI = wanninayakegcb @ gmail com

Can anyone tell, During Exam Can go back and forth between questions OR do we have to answer them as they appear. I was wondering if i could skip the tough questions and come back on them later ??

@ Shadows, NO you can not, once you finish a question it is it. there is no going back to review.
@Thomas, how legit is your comment, can you back it up with a valid free link?
@New Dumps, Cant you give it a rest already. we are done trying to pay for things like this.

Anyone have a link to the questions Dave made? I believe it ran in browser and used an index file to run. Thanks

http://p30download.me/udemy-cisco-ccna-icnd1-100-105-version-3-0-download/ just downloaded these tutorials and am super psyched. will sort these out then do Dave’s dump, then the 272q and then a cheat sheet and boom I am a CCENT. already set the exam date for 12th Nov. Let get it.

@kik
If you have a frame with 1600 bytes of payload, and add 18 bytes of header and trailer, its ok. But if you add a vlan tag (4) you can cause a baby giant error.
Its the same about standard frame, 1500 standard +18 its ok, but if you add a vlan tag 4, it cause a standard frame error.
So 1518 can cause a standard frame error, and 1600 a baby giant error.
You can try these configurations in packet-tracer.

@Luke Cage, nice one. I hope to do mine before then so expect my feedback

taking the test today !!

Anyone tried to get extra minutes for the ccent exam ? If you are from no-native English country do you automatically get extra minutes ? Anyone

@NICK
is a NO_NO if you have in USA over 2 Years!!

@CISCOTTE
Tap0ut is right
Two hosts are attached to a switch with a default configuration. Which statement about the configuration is true?
A) IP routing must be enabled to allow the two hosts to communicate (switch is a L2 device..noly knows MAC , so no IP)
B) The two hosts are in the same broadcast domain (correct same vlan 1)
C) The switch must be configured with a VLAN to allow the two hosts to communicate (no need cause vlan1 is default)
D) Port security prevents the hosts from connecting to the switch (port security is disabled by default)

@CISCOTTE
I’m taking the test this month of november…got the voucher already

@Nick
Yes, you do get extra minutes in a no english speaking country!

PL413r

HOW?? Believe or NOT is what they told me and I have spoked to them directly – NO if you have been in USA over 2 Years!! I could use it!!!
CISCO CANDIDATE CERT: 800-553-6387

PL413r

But maybe you are in a no english speaking country???

@CISCOTTE
I am in a non english speaking country brother,
Yes, they give me a 30 minutes extension…they call it “Time extension for non-native English speaker living in non-English-speaking country”

my exam is this sunday
can anyone please send me the valid dumps for icnd1 100-105
my gmail is {email not allowed}

@dave
can u please send me the valid 100-105 dumps

@PL413r

Thanks, I see!!! To all of us just Lets Do It anyhow!!! SOON!!!

@Dave
Can I also have the valid 100-105 dumps?

QUESTIONS 1 – couldn’t get the right answer from my CISCO search??

1) If Cisco E.F. (CEF) is enable what will be automaticly disable?

Might be OBVIOUS Question? But when we take the TEST do we have to do:” copy running-config startup-config” SAVE anyhow even NO config for Teslet & Simlet??

@There is no Dave anymore, he has moved on to icnd2

Does anyone have the last Dave dump that they would like to share?

@CISCOTTE check this link https://routing-bits.com/2009/06/02/understanding-cef/

Crystal clear explanation…
What really matters in understanding CEF , is to keep in mind that SWITCHING in a ROUTER ( or forwarding packets ) , is the process of receiving a packet in one interface and forwarding it out of another interface .
CEF is like a copy of the routing table ( layer 3 information ) and adjacency table includes MAC ( layer 2 ) information. So CEF is a mechanism that speed up this decision (find the right output interface) by actually building these two tables (CEF and adjacency) and finally combine them.
(To go a little further , CEF and adjacency tables are built during the convergence of a network and have optimized lookups so that recursive lookups are avoided , which is one more advantage over the other method

Not Dave?

Thanks you! But DAVE you DIDN’T answers my Q. – everything YOU said was posted online and I can’t find answers to this question:

Q.) If Cisco E.F. (CEF) is enable what will be AUTOMATICLY disable?

Hi Guys…
I just did it and pass my ICND! 100-105 exam yesterday
I am really busy preparing for ICND2, BUT, I really wanna help others as others REALLY helped me..
I will try my best to remember what questions I had
A- From Pass Leaders pdf files, I had the following questions numbers (2-3-8-9-14-15-16-18-27-31-36-47-49-53-68-69-72) and simlet was the questions (95-96-97-98).
There were some questions about finding subnet address but I really don’t remember which ones but they are on the range (33-41-76-103)
B- From Gratis Exam pdf file, I had the following questions numbers (1-5-8-12-14-19-22-24-26-30-31-32)
C- There was a question about successful ICMP, the answers were differ from 1 second to seconds and I guess the correct answer was for the sender to send echo and the reciever echo reply within 2 seconds…but not sure yet
D- There was a question about Vlan creation…
what will be the output of the following
Switch1(config)vlan 10
Switch1(config-if)do show vlan
E- There was a question about router on a stick but I really don’t rememeber it…
F- There was a question to which statement is true about routing protocols, and answer was that OSPF is a link state protocol. I think it is in one of the files
G- There was a question which routing protocol notation has the lowest administrative distance, I guess it is (D) EIGRP…

Best of luck to all..

@MaMoShka, Tanks & CONGRAT!!!!

@CISCOTTE If Cisco E.F. (CEF) is enable what will be AUTOMATICLY disable?

process switched mode that will be disabled

@whittakerlap

Thanks you!!! do you have a link about it for me?

@whittakerlap

Mayby my Question was ” commun sence ” ??

I will send you a link

copy and paste this Difference between PROCESS SWITCHING, FAST SWITCHING and CEF

into g o o g l e

Dave can you please link the ICND1 quiz again, the old links are not working. Please and thank you!

@whittakerlap – Thank you!

can anyone please send me the latest icnd1 100-105 dumps?
thanks

Hi all,

Today I took my ICND 100-105 today.
I passed scoring 906 out of 1000.

I like to thank @dave and everyone else who contributed in the quiz simulations and took part in giving information and what to except in this exam.

Most of the questions I got were pretty much the same as the quiz @dave put up with about 5 or 6 different questions.

The sims I got a NAT,NTP ,Security logins and ACL .

How I studied was I read the study guide and Udemy Chris Bryant CCNA BOOT CAMP , Alpha Prep and did the quiz that was supplied here.
Thank you everyone again and if you have any questions feel free to ask as I will help as much as I can.

Cheers,
Seba

@m&m

https://www.dropbox.com/s/a5puza67n5cyu6k/ICND_1_PACKAGE.zip?dl=0

@MaMoShKa,

Thanks for sharing the information, it helps a lot.

Just curious, EIGRP and OSPF are not part of ICND1 100-105 exam, i wonder why did you had questions from these two topics.

just for practice I guess, you never know what Cisco can throw at you when you are in the cubicle by yourself.

hello which dump you learn? please

@SebaVeron hello which dump you learn? please

@shadows

It was a question about administrative distance issue, not in details about the protocols.

and I am not sure if there were S or C in the choices, if they were, then C will be the correct answer

@PL413r

Have you double check it on your ROUTER?

YOU: October 31st, 2016
Which two commands will display the current IP address and basic Layer 1 and 2 status of an interface?( Choose two)
A. router# show version (just wrong)
B. router# show ip interface X
C. router# show protocols (wrong command right is sh ip protocols)
D. router# show controllers X
E. router# show running-config (doesnt show l1)

HE SAID:Tap0ut – November 1st, 2016
show protocols and show ip interface are most certainly correct

@shadows
You need to know Administratives Distances of those protocols, cause they can be on ICND1.

@SebaVeron
If we helped you so much please share all diferent questions you remember you had on your test. Please!

@CISCOTTE
Yes bro, i checked on our Catalyst 2960 and CCIE teacher.

@PL413r

Thanks PAL! ( interface & controllers ) I’ll take my 105 B4U_DO!!!!….WILL KEEP U POSTED!!!

@PL413r

Like Tap0ut said I just checked AGAIN on my Cisco Packet Tracer & you are 100% RIGHT PL413r Thanks again!!

I just failed – 825/832

I got the NTP/DHCP/Access list labs

only 1 IPV6 question –
Ill post up more questions as I remember

what is the best #show command to verifiying NTP?

beside #sh ntp status

just passed!

@XCISCOX tell us more

Thank you Dave! Appreciate it.

I really wish if in the actual exam we could get a chance to come back to our questions for review OR if we could skip the tough questions to save time and attempt them later.

please share me the link for dave icnd1 dumps

The exam is tough, only 35 questions on here. you need another 7 questions to pass. best advise is to keep studying all the questions on here.
no coming back to the questions is a killer, no reviews so best waiting for me to confirm again next in 3 weeks time.Good luck

I havent got money maybe if I get a voucher I will take it early

please helpme where i can find 100-105 dump?

you need to look for francis link on here

Took the ICND1 100-105 exam today was asked 54 questions and had to make an 832 and passed with 900+ score. I spent the average test taker’s four months studying a few hours each night and several entire weekends over those four months. There is no shortcut (i.e. studying dumps) for this exam, so don’t bother with dumps free or paid they are a distraction. I have reviewed all posted here and none were as useful as focused studying. Most of the dumps or links to dumps you find here all have a lot of irrelevant material from older exams so you will go off track studying dumps. You must know the key topics from the Wendell Odom Official Cert Guide books PERIOD. In addition to knowing the key topics you MUST have hands on from equipment or a simulator. I highly recommend Boson’s simulators as they worked wonders for me. I also recommend Boson’s practice exams as they are the closest to the real exam as you can get. Boson’s practice exams are harder than the real exam and the Pearson IT practice exams that come with the Wendell Odom books are much harder than the real exam. Both Boson and Pearson practice exams are highly useful in study mode so use them if you have them. Good luck! On to begin mastery of ICND2!!

Hi,
can anyone please share the link from @Dave material , i cant seem to open any of his previous links

Go sell your crap somewhere else idiot!

So apparently Dave’s dumps don’t work anymore cuz of Dropbox. Does anyone have a copy on google drive or something?

Hello everyone,

Just passed ICND1 a few hours ago with a 860/1000. Wasn’t the best score ever but a pass is a pass. As far as my test went, @Dave was the Game Changer here because he had practically everything you need from this test. The SIMs I had dealt with NAT, NTP, DHCP, and ACLs. I would say at least 75% of the test consisted of the quiz, practice labs, and SIMs @Dave provided. Also some of the questions from the 274q VCE practice test were up there so study that as well. I can’t think of questions that weren’t covered here, but when I do think of them I’ll be sure to let you know. Good Luck to you all!