Share your ICND2 v3.0 Experience

@ Dave 3, Thanks for your usual help, the drop-box links in your previous post are not working

How can you disable DTP on a switch port?
A. Configure the switch port as a trunk.
B. Add an interface on the switch to a channel group.
C. Change the operational mode to static access.
D. Change the administrative mode to access.
Answer D
explanation:
Administrative Mode: dynamic auto
Operational Mode: static access
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: native
Negotiation of Trunking: On
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: On
Administrative Mode: static access
Operational Mode: static access
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: native
Negotiation of Trunking: Off

@ Dave

Still waiting for more update.

Håkon Møller please send me the pdf dump 346q. i will take my exame next month
send on my email sergio_carlos22 at Hotmail.com thanks

Hello Dave3

Where are you? Please, I need your help.

@ Anon52

Still waiting for the rest of the questions. Thanks…..

Im taking the exam this week. Are the dumps posted in the previous pages valid?

Hi Can Some please share CCNA v3.0 book.
Thank you

CCNA Routing and Switching Complete Study Guide 200-105
https://drive.google.com/file/d/0B6mnbxOlbXoxWnZtZTl6bzBnNVU/view

Get Latest new dumps at only 10usd now. Valid material at below page with labs in packet tracer
remove asteriks
icnd1-2.b*l*o*g*s*p*o*t*.*c*o*m

How do we do the math in exam ?? Are we allowed/given any piece of paper to do the conversions ??? How does it work ?? Seniors please help out

about this questions:

1) Routers R1 and R2 are on the same network segment, and both routers use interface GigabitEthernet0/0. If R1 loses communication to R2, which two items should you check as you begin troubleshooting? (Choose two.)
A. Verify the R1 and R2 both are using HDLC encapsulation
B. Verify that the R1 GigabitEthernet0/0 interface is up and the line protocol is down
C. Verify that the R1 GigabitEthernet0/0 interface is up and the line protocol is up
D. Verify that the GigabitEthernet0/0 interfaces on R1 and R2 are configured with the same subnet mask
E. Verify that R2 is using 802.1q encapsulation

The correct answers : B & C – I think.

2. After you configure a new router to connect to a host through the GigabitEthernet0/0 port of the router, you log in to the router and observe that the new link is down. Which action corrects the problem?
A. Configure the host to use R1 as the default gateway
B. Use a straight through cable between the host and R1
C. Use a crossover cable between the host and R1
D. Use a rollover cable between the host and R1

Correct Answer: C – I think.

** I’d love to get second opinions about this questions.. please.. and thanks! **

Package Include:

ICND1 (100-105) = 239Qs and 201Qs
ICND2 (200-105) = 110Qs and 204Qs (Updated 11th November )
Latest Dumps in Both PDF & VCE Format.
Working VCE Player
All LABS TOPOLOGIES for Packet Tracer 6.0.1
All time EMAIL Support for any querry.
You will also get free updates for 60 Days, starting from your contribution date.

If anyone interesting let me know.
FYI = wanninayakegcb at gmail dot com

@Eliran U need crossover cable only with the same devices Example : Switch / Switch or Host /host I Think a ist the correct answer

The first Question i think C and D are the correct one.

Regards Ghosy

First question answer was B not A sry

Anyone taken the test so far,if yes kindly share experience

I have atest on monday for 200-105 i request all if anyone has valid dumps and online tests please share

Hi did the exam today and did not make it. Dumps are still valid but there are a few new questions.

Like: maximum hello and dead timers of ospf, a variant on the ip sla icmp echo question and inter vlan slowness.

Got the 4 eigrp and ospf labs.

Going for the 2nd try on tuesday.

@kraken how much did u score?

@kraken
Sorry to hear you missed it. Next time! Which dumps are you referring to? The ones that Dave put up or the other ones?

@Eliran
1) Routers R1 and R2 are on the same network segment, and both routers use interface GigabitEthernet0/0. If R1 loses communication to R2, which two items should you check as you begin troubleshooting? (Choose two.)
A. Verify the R1 and R2 both are using HDLC encapsulation
B. Verify that the R1 GigabitEthernet0/0 interface is up and the line protocol is down
C. Verify that the R1 GigabitEthernet0/0 interface is up and the line protocol is up
D. Verify that the GigabitEthernet0/0 interfaces on R1 and R2 are configured with the same subnet mask
E. Verify that R2 is using 802.1q encapsulation

The correct answers C and D

The source IP address used by the neighbor’s Hello must be in the same subnet as the
local router’s interface IP address/mask

@someguy: Yeah the ones from dave and leadpass.

@zaheer: I scored 694 on the test.

@ToF

Thank you so much.

and the second question:

After you configure a new router to connect to a host through the GigabitEthernet0/0 port of the router, you log in to the router and observe that the new link is down. Which action corrects the problem?
A. Configure the host to use R1 as the default gateway
B. Use a straight through cable between the host and R1
C. Use a crossover cable between the host and R1
D. Use a rollover cable between the host and R1

Correct Answer: C – I think.

@kraken you paid $100 for the lead pass dumps or did you find it cheaper somewhere else?

I know this is the 200-105 exam but does anyone use pineapple’s 130q for the 200-125 exam? a lot of questions seem to be the same.

I failed icnd2 with 790 can anyone pliz advice or share some Latest dumps thanx in advance

After you configure a new router to connect to a host through the Gigabitethent0/0 port of the router, you log in to the router and observe that the link is down

A. Configure the host to use R1 as the default gateway
B. Use a straight through cable between the host and R1
C. Use a crossover cable between the host and R1
D. Use a rollover cable between the host and R1

Correct answeris D

We only use a crossover for
router to router
Switch to Switch

We only use a rollover or straight through for
Switch to Host
Switch to Router
Router to Host

@King
Rollover normaly use to connect to the console Port

for Switch Host / Switch router etc yout take a Straight through (Patchcable) cable

so in this question Answer B ist the correct one

Experts, please give tips on how to manage time during Exam because questions are random and you cannot go back so if my first question is a simulator, that will take quite a bit. Also Is there anyone who was short of time and couldn’t answer all questions?

Failed yesterday @755 🙁

@King/Eilran

A. Configure the host to use R1 as the default gateway
B. Use a straight through cable between the host and R1
C. Use a crossover cable between the host and R1 Switch or Hub
Router->Switch or Hub
Rollover is for console port

Aslam which question came out? which dump is valid? Please share

Hello

Where is Dave3 and Anon52?

After you configure a new router to connect to a host through the Gigabitethent0/0 port of the router, you log in to the router and observe that the link is down
A. Configure the host to use R1 as the default gateway
B. Use a straight through cable between the host and R1
C. Use a crossover cable between the host and R1
D. Use a rollover cable between the host and R1

Correct answer is C
PC to Router = Ethernet Cross-Over

https://learningnetwork.cisco.com/thread/13249

@ i studied 346q & 130 q ,many were from there a few new questions i dont remember

1 ppp 1 eigrp simlet also dhcp was there

@cyril one question was below

Which statement about DTP is true?

A. It uses the native VLAN.
B. It negotiates a trunk link after VTP has been configured.
C. It uses desirable mode by default.
D. It sends data on VLAN 1.

Answer : D

I am not sure about answer but saw in dumbs

Which two circumstances can cause collision domain issues on VLAN domain? (Choose two.)

A. duplex mismatches on Ethernet segments in the same VLAN
B. multiple errors on switchport interfaces
C. congestion on the switch inband path
D. a failing NIC in an end device
E. an overloaded shared segment

Answer: AC

Does anyone have a pdf of the Todd Lammle book?

Which statement about DTP is true?
A. It uses the native VLAN.
B. It negotiates a trunk link after VTP has been configured.
C. It uses desirable mode by default.
D. It sends data on VLAN 1.

Answer : A

@ Aslam
Thank you, can you please share the 346q & 130 q

@ToF
Why A. In default the native Vlan is Vlan 1. D could be correct too, or?

@all
If any have cbt nuggies videos for icnd2 pls share it

Which Cisco platform can verify ACLs?
A. Cisco Prime Infrastructure
B. Cisco Wireless LAN Controller
C. Cisco APIC-EM
D. Cisco IOS-XE

C?

Hey guys! are parts of the old dumps valid ? im studying for the icnd2 and if it helps at least a bit then ill go through them if not then back to the books 🙂

@Ghosy
Which Cisco platform can verify ACLs?
A. Cisco Prime Infrastructure
B. Cisco Wireless LAN Controller
C. Cisco APIC-EM
D. Cisco IOS-XE

Answer : C

The one exam topic that mentions an APIC-EM app uses a longish phrase: “APIC-EM Path
Trace ACL Analysis tool.” This phrase refers to a newer app (not available in version 1.0 or
1.1 of APIC-EM) that takes the work done by Path Trace a step further.

@ghosy

VLAN 1 is always present on the trunk port. If the port is trunking in ISL mode, DTP packets are sent out on VLAN 1. If the port is not trunking in ISL mode, the DTP packets are sent on the native VLAN (for 802.1Q trunking or nontrunking ports).

The Quiz from Dave have some Errors than. Example question 4 and 20 are still the same (20 has the correct ansers)

@ToF

Which Cisco platform can verify ACLs?
A. Cisco Prime Infrastructure
B. Cisco Wireless LAN Controller
C. Cisco APIC-EM
D. Cisco IOS-XE

Answer : C – look ToF .. look on the question.. APIC-EM is tool.. feather! .. not platform.

i think “Cisco platform” – is D. Cisco IOS-XE !

answer : D.

CISCO platform is cisco ios-xe.
i think.. just game in the question and the words.

@ToF

Which Cisco platform can verify ACLs?

A. Cisco Prime Infrastructure
B. Cisco Wireless LAN Controller
C. Cisco APIC-EM
D. Cisco IOS-XE

Answer : D ! Cisco platform – cisco ios-xe

Explanation:

http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_data_acl/configuration/xe-3s/sec-data-acl-xe-3s-book/sec-access-list-ov.html

please check this again..

C

@Eliran

Cisco APIC-EM is a plaform they call it the Cisco APIC-EM platform

Would like to start off by saying thanks to every one that has posted questions from the v0.3 ICND2 exam. Its been a big help. I took the exam and failed with a 796 out of 811 to pass. I did manage to write down several of the questions as soon as I came home but am having no luck in finding their solutions in my curriculum, probably because the wording is different. Yes, I took the class. but allot of the material was not covered for some reason. Anyhow, this is an intro post to check if guests can post on here as well. Will add questions in another post.

@JonNetNuub were there any questions from the new 9tut.net post regards icnd2v3? Thnx

@ToF and @Eliran

Which Cisco platform can verify ACLs?
A. Cisco Prime Infrastructure
B. Cisco Wireless LAN Controller
C. Cisco APIC-EM
D. Cisco IOS-XE

Answer: B. Cisco Wireless LAN Controller
The wireless LAN Controller are used to control / restrict access with the WLAN. You can verify the ACL on the ACL web page to check that the configs were placed on the interface.

The Cisco APIC-EM supports both extended and standard IP ACLs. The controller configures policies
from the northbound using only extended ACLs (IP). The controller reads both extended and
standard ACLs (IP) from the southbound.

Source Link : developer.cisco.com/fileMedia/download/7f047ce5-7bca-4c7d-9a44-a43273546217

@all
Pls share me cbt nuggies videos link

@JonNetNuub are you going to post? I only ask because it looks like you speak clearly so I am curious to see your take on the test. I also want to know what materials you used.

Current attending a Boot Camp and the APIC-EM came in our lesson. Here is what i got from the instructor.

Which Cisco platform can verify ACLs?
A. Cisco Prime Infrastructure
B. Cisco Wireless LAN Controller
C. Cisco APIC-EM (Correct)
D. Cisco IOS-XE

Lately, many different software-defined networking (SDN) controller platforms have emerged. Cisco Application Policy Infrastructure Controller Enterprise Module (Cisco APICEM) is one of them. It is a Cisco SDN controller for enterprise networks—access, campus, and WAN .

The following are some features of Cisco APICEM:
– ACL analysis: Accelerates ACL management by querying and analyzing ACLs on each network device. It can quickly identify ACL misconfiguration.

Its a platform with features to monitor ACLs. I hope this helps.

@Pascal357
Thanks

Taking this in a few days. This chat doesn’t seem too lively without Dave. Can anyone who has taken the test and failed reveal which dumps to practice and which to avoid?

Hello,

Does anyone have dumps and or study packages??? Thanks

You enter the show ipv6 route command on an OSPF device displays a route. Which conclusion can you draw about the environment?

OSPF is distributing IPv6 routes to BGP.
The route is designated as an ABR
The router is designated as totally stubby.
OSPFv3 is in use. (correct)?

In Daves test the rist answer is correct. I think the last one ist the correct one.

Dumps4Download provide latest 200-105 exam questions if you need to download it visit this link https://www.dumps4download.us/free-200-105/cisco-question-answers.html

What are two drawbacks of implementing a link-state routing protocol? (Choose two.)
A. the sequencing and acknowledgment of link-state packets
B. the high volume of link-state advertisements in a converged network
C. the requirement for a hierarchical IP addressing scheme for optimal functionality
D. the high demand on router resources to run the link-state routing algorithm
E. the large size of the topology table listing all advertised routes in the converged network

Which statement about DTP is true?
A. It uses the native VLAN.
B. It negotiates a trunk link after VTP has been configured.
C. It uses desirable mode by default.
D. It sends data on VLAN 1.

I think the answer is A (not D). DTP’s message is transmitted in a native Vlan.
Vlan 1 is only setup as a native Vlan by default which can be changed.

When you guys update the site about icnd2 200_105

Just had a look at the questions, lets discuss them.

Which feature can you use to restrict SNMP queries to s specific OID tree?

A. A server group
B. An access group
C. A community
D. A view record <

Which configuration enables OSPF for network 192.168.1.0/24

A. router ospf 1
Area 0 virtual-link 192.168.1.0
B. router ospf 1
Network 192.168.1.0 255.255.255.0 area 0 <
C. router ospf
Router-id 192.168.1.0
D. router ospf 1
Neighbor 192.168.1.0

Which three options are types of slow VLAN connectivity? (Choose three.)

A. slow inter-VLAN connectivity <
B. slow collision domain connectivity <
C. slow broadcast domain connectivity <
D. slow default gateway connectivity
E. slow application domain connectivity
F. slow routing domain connectivity

Which type does a port become when it receives the best BPDU on a bridge?

A. The backup port
B. The alternate port
C. The root port <
D. The designated port

Which statement about VLAN configuration is true?

A. Dynamic inter-VLAN routing is supported on VLAN 2 through VLAN 4064
B. A switch in VTP transparent mode saves the VLAN database to the running configuration only
C. The switch must be in the VTP server or transparent mode before you configure a VLAN <
D. The switch must be in config-vlan mode before you configure an extended VLAN

Which statement about the IP SLAs ICMP Echo operation is true?
A. It is used to identify the best source interface from which to send traffic to a destination
B. It is configured in enable mode
C. It is used to determine the one-way delay between devices <
D. The frequency of the operation is specified in milliseconds

Which WAN technology uses labels to make decisions about data forwarding?
A. Frame Relay
B. MPLS <
C. VSAT
D. Metro Ethernet
E. ISDN

After you configure a new router to connect to a host through the GigabitEthernet0/0 port of the router, you log in to the router and observe that the new link is down. Which action corrects the problem?

A. Configure the host to use R1 as the default gateway
B. Use a straight through cable between the host and R1
C. Use a crossover cable between the host and R1 <
D. Use a rollover cable between the host and R1

Which value can you modify to configure a specific interface as the preferred forwarding interface?

A. The VLAN priority
B. The interface number
C. The hello time
D. The port priority <

Which VLAN bridge priority value is assigned by the set spantree root command?
A. 16384
B. 32768
C. 28672
D. 8192 <

Which two statements about the spanning-tree bridge ID are true? (Choose two.)

A. The bridge ID is transmitted in the IP header to elect the root bridge
B. The bridge priority must be incremented in blocks of 4096 <
C. It is composed of an 8-bit bridge priority and a 16-bit system ID extension
D. The system ID extension is a value between 1 and 4095
E. It is composed of a 4-bit bridge priority and a 12-bit system ID extension <

Routers R1 and R2 are on the same network segment, and both routers use interface GigabitEthernet0/0. If R1 loses communication to R2, which two items should you check as you begin troubleshooting? (Choose two.)

A. Verify the R1 and R2 both are using HDLC encapsulation
B. Verify that the R1 GigabitEthernet0/0 interface is up and the line protocol is down
C. Verify that the R1 GigabitEthernet0/0 interface is up and the line protocol is up <
D. Verify that the GigabitEthernet0/0 interfaces on R1 and R2 are configured with the same subnet mask <
E. Verify that R2 is using 802.1q encapsulation

New copy of the quiz, might be some wrong answers. Check carefully and discuss here.

https://www.dropbox.com/s/8j81q6o5tsog7dg/ICDN_2_QUIZ.zip?dl=0

what file are they

Cant open it dave4

Should just be able to download the .zip file and place on in a folder. Then open the web browser file and should work.

Wow, great stuff, will inform you of any queries

Is A the Answer?
QUESTION 26
How can you disable DTP on a switch port?
A. Configure the switch port as a trunk.
B. Add an interface on the switch to a channel group.
C. Change the operational mode to static access.
D. Change the administrative mode to access.
Answer: A

On this question I think there is no right answer?

Which configuration enables OSPF for network 192.168.1.0/24
A. router ospf 1
Area 0 virtual-link 192.168.1.0
B. router ospf 1
Network 192.168.1.0 255.255.255.0 area 0 <
C. router ospf
Router-id 192.168.1.0
D. router ospf 1
Neighbor 192.168.1.0

According to this.

http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_ospf/configuration/12-4t/iro-12-4t-book/iro-cfg.html#GUID-51A06D7A-7099-453C-A9FD-34CE45080796

I thought they removed frame relay from the exam objectives for the new 200 105, i am seeing frame relay question in the leadpass 346 question. can anyone answer?

Dave is back!

all dumps are with frame relay, alle dumps are 70% valid not more.

Frame relay are no objective of the exam

Ghosy…the dumps Dave just post are 70% valid or the old? Or one I did not mention?

How can you disable DTP on a switch port?

A. Configure the switch port as a trunk.
B. Add an interface on the switch to a channel group.
C. Change the operational mode to static access.
D. Change the administrative mode to access.

Only information I could find on this, makes me think A is the answer. If you enter “switchport mode trunk” this will disable DTP.

https://learningnetwork.cisco.com/thread/58463

Which option is a benefit of switch stacking?

A. It provides redundancy with no impact on resource usage.
B. It simplifies adding and removing hosts.
C. It supports better performance of high-needs applications.
D. It provides higher port density with better resource usage.

Answer: D – ?

Just passed 200-105 today. I used only Dave’s ICDN2 package and reviewed his new quiz this morning. ~70% of dumps are still valid. Sims include EIGRP, OSPF and a simlet on troubleshooting PPP/multilink.

@Eliran

Which option is a benefit of switch stacking?
A. It provides redundancy with no impact on resource usage.
B. It simplifies adding and removing hosts.
C. It supports better performance of high-needs applications.
D. It provides higher port density with better resource usage.

Answer is: D.

Which feature can you use to restrict SNMP queries to s specific OID tree?
A. A server group
B. An access group
C. A community
D. A view record < (No idea about this question, can u pls explain it)

After you configure a new router to connect to a host through the GigabitEthernet0/0 port of the router, you log in to the router and observe that the new link is down. Which action corrects the problem?
A. Configure the host to use R1 as the default gateway
B. Use a straight through cable between the host and R1 <
C. Use a crossover cable between the host and R1
D. Use a rollover cable between the host and R1

Which VLAN bridge priority value is assigned by the set spantree root command?
A. 16384
B. 32768
C. 28672
D. 8192 < (why 8192, any other values can be the bridge pirority, and 32768 is set by default)

How can you disable DTP on a switch port?

A. Configure the switch port as a trunk.
B. Add an interface on the switch to a channel group.
C. Change the operational mode to static access.
D. Change the administrative mode to access. < (when a switch port is configured as a trunk, it still send DTP message to help the other side to choose to be a trunk. By changing the mode to access, the link will never be a trunk.)

Which option is a benefit of switch stacking?

A. It provides redundancy with no impact on resource usage.
B. It simplifies adding and removing hosts.
C. It supports better performance of high-needs applications. <
D. It provides higher port density with better resource usage.

My bad, crossover cable is the correct answer

After you configure a new router to connect to a host through the GigabitEthernet0/0 port of the router, you log in to the router and observe that the new link is down. Which action corrects the problem?
A. Configure the host to use R1 as the default gateway
B. Use a straight through cable between the host and R1
C. Use a crossover cable between the host and R1 <
D. Use a rollover cable between the host and R1

@Wayne the old dumps

@ Dave4, are the new 70 questions filtered from the 364 questions?

Pass your exam on first attempt.
These are valid exam questions. Visit below page and download dumps instant:

remove as-teriks
icnd1-2.bl*ogspot.c*om

@Dave4

#23
While troubleshooting a switch, you executed the show interface port-channel 1 etherchannel command and it returned this output. Which information is provided by the Load value?

a. The percentage of use of the link
b. The preference of the link
c. The session count of the link
d. The number source-destination pairs on the link

I believe this should be A, not D.

@Dave4
Question 25

The Correct answer is Switch4, port fa0/2 and not Switch4 port fa0/11

Because the sending view (Port Priority from Switch3) is important, not Switch 4.
Switch3 fa0/12 prio is 128.14 (128. (2 (default) + portnumber)
Switch3 fa0/1 prio is 128.3
so on Switch4 fa0/2 is the(blocking (spt)) discarding role.

i hope its correct

Is this true? and why?

QUESTION 149
Refer to the exhibit. What is the most appropriate summarization for these routes?

10.0.0.0
10.0.1.0
10.0.2.0
10.0.3.0

A. 10.0.0.0 /21
B. 10.0.0.0 /22
C. 10.0.0.0 /23
D. 10.0.0.0 /24
Answer: B

@All
Hello Guys! I just passed ICND1 and I’m kind of broke right now…do you guys have any good ICND2 training that you could share? Like CBT.

Thanks @Dave

I passed today with Dave1’s study guide. It was 90% of my test. There were a few other questions that were not on the guide one was an HSRP and another about root ports. The labs I got were 2 OSPFs, and 1 GRE. The question were not exactly the same as the ones on 9tut, so be ready. Finally I only got 813 out of 811, so I suspect that some of Dave1’s answers are incorrect. Regardless of the score, a pass is a pass; Thanks Dave1!

Good Luck

@KTeazy

Congrats on passing! I take mine on Friday. Did you use Dave4’s quiz or the two question dumps?

Thanks!

@kteazy did you use the old quiz he posted or the one he recently posted a few days ago?