Share your ICND2 Experience

I have to add one more thing about switches.
I have realized I didn’t put the gateway in the switch which was very stupid .. hahaah but I just forgot anyway..
cheerz people.

is there anyone that has a current IT job in USA?

I recalled a problem. hopefully, it helps those who prepare exam soon

Router – SW1 -SW2 (vtp domain client setup / IP setup / Lasted avaiable IP for SW2)

Connect each SW1 and 2

vtp mode client (to setup client mode)
vtp domain xxxx (change domain name)
assing IP / default gateway for SW1

conf t -> ip default-gateway x.x.x.x
interface vlan 1
ip address x.x.x.x 255.255.255.240 (?) -> You need to calculate which valid IP address you can use through another switch since they are same network. Subnet Mask, you can grab from the other switch. gateway (you can try cdp neighbor details for router)

Frame Relay

show frame-relay map
you can find out dlci information. I don’t remember rest.

Especially

NAT simulation, i;ve never seen.

I took the test 2 weeks ago and missed by about 40 points :(.

I had the VTP sim where you had to configure the switch.

I had the Frame Relay simlet / hotspot that is on this site under the CCNA portion.

I can’t remember for the life of me what the 2nd simlet I had was.

Can anyone who recently( since Sept. 1st) took the test recall what they had and give a description I am retaking the test and want to prepare for it. I want to say it was OSPF but the poster who described it on page 2 doesn’t sound firmiliar. Thanks.

Actually disregard my last post after thinking about it. The poster on page 2 had the same sim.

The first part asks about the router ID. It gives you 3 172 address and 1 192 and asks which would be the ID.

Reference his post for that sim.

Sorry for making a 3rd post. But I now remember what I had.

ISP—-Router 1——Router 2
| |
router 3 router 4
| |
SWITCH

Router 1 had a few subnets. Router 2 had a few subnets. Router 2 had a link to router 3 and router 4. Router 3 & 4 each had a link to a switch in the same subnet.

After thinking my OSPF sim questions where this.

1. What is the ID of router 1?
A. 192.x.x.x
B. 172.x.x.x
C. 172.x.x.x
D. 172.x.x.x

2. I don’t remember what this was.

3. How does OSPF affect switch 3 & 4?

I don’t remember all of the options. I know one was they form neighbors. (which I believe is correct)

4. How many routes does router 1 have in its routing table.

This has a few options. 4, 5, 6, 10 I believe.

Like I said this was a few weeks ago and my memory is blurry. If anyone who recently took this test and had the same simlet can fill in a little better please do.

Thanks!

My diagram didn’t come out the same as when i had it typed.

The two bars to Router 3 & 4 should be coming off router 2. They each have a link to the switch.

I got frame-relay sim (I believe this is same as I saw, but if not, plz reply)

1. What destination Layer 2 address will be used in the frame header containing a packet for host 172.30.0.4?

show frame-relay map and check DLCI value

2. A static map to router B location is required. Which command should be used to create this map

frame-relay map ip x.x.x.x (router B) DLCI (through show frame-relay map) broadcast

!!! remember, if the router is set by sub-interface, you should use below
frame-relay interface-DLCI xxxx

3. Which connection user the default encapsulation for serail interfaces on Cisco router?

HDLC (default encapsulation)

show running-config or show frame-relay map

@gwbaby

This was on my test as well in addition to the OSPF. I was referring more to the OSPF then the frame relay.

If you look at the actual CCNA test(802) section of 9tut they have the simlet. Different IP’s and DLCI’s but the same structure and questions.

cisco dude, dude, gwbaby, and others that have taken the test, I took the test a couple days ago, i also missed it by a very small margin. my email is jrs711@live.com. I would like to compare notes about what i saw on the test and what you saw and ask questions, in doing so maybe we can cover more bases to ensure that if there are variations to the tests we have covered most of those. its easier to do this by email. I plan on taking the test again, but need more info. If you like to work together. shoot me an email. Sorry I dont come on this site that often.

@ Jcisco … oK I will add you on msn later on when I get back from work.
I will take all the dumps I have and see what were in the exam. and I might find a way to to edit these .vce files so I can sum up a single dump.
talk to you laters

I sent already email. to Jcisco. I will sum up too. let us see how much we can remember.

@ everybody.
One thing that I noticed is now 640-802 (CCNA) dumps were added to ICND2. I saw these problems.

Passed the ICND2 today w/ 915, still had a problem with time. Just barley completed it. Some of the questions were from the first test that I failed w/ a 811 but just glad to have it out of the way. Thanks to 9tut, CBT nuggets, and a few dumps for pratice. It works!

On to the CCNP…..

Just emailed Jcisco as well.

thanks dude for your response..

@B

Do you remember hot spot for NAT?
Do you remember OSPF sim?

your feedback will be helpful. thanks.

Download links for testing material – http://www.careercert.info/2009/08/ccent-icnd1-icnd2-practice-tests-and.html

has anyone recvd any updates at all from Pass4sure, passguide, testking or actual tests. I emailed a couple of them. One said – “Their material is current and has 90% pass guarantee” and I was like – “Idiot, this is not what I asked :)” Another one never got back to me.

@dude

The link you put up for the ccna dump.. are you saying that the questions on there are from the recent test or are you saying just the ip routing questions on the dump are from the test?

Just clairifying I take it the 2nd time in the the morning. Any feedback on a good dump with questions on this recent version of the test would be appreciated.

@kellyboy: yeah there are real exam questions in that section of ccna dump.

Hi…
I think use Testking for study…
Can It Work version 6?
Which Dump brings more test questions?

@dude
Thanks.

@3lm4m4r14

Until now, 9tut and the posts here above for labs, Actual test 1.9, actual test 08/09/2009, Brainddump by W1zard and Certify me 640-802 by Widget for questions is the best combination. I think we cover 80% of real exam questions.
I know it is a big workload but this is the best we have and do up to now.

I took the test failed and retook it within the last month. Each time the test questions were totally different expect for the OSPF and Frame Relay Simlet and the VTP Lab. I would say I saw the majority of the questions between multiple dumbs, but not all in one place. From others I have talked to recently they seemed to have different tests from questions we compared. Most have came from the CCNA 802 test.

@amerigo
Thank for reply me…
The Actual test that you tell me is for 640-816?
I will take 640-816 (ICDN2) on November
Anyway you recommend me those?
Can I use P4S 2.77?

Thanks for reply

@3lm4m4r14

yeah, both AT are 640-816. P4S 2.77 is not necessary at this moment. By the way, since you wanna take your exam on november, i suggest you to wait new dumps we are searching for. Maybe the great Dude and other friends will be able to find out a better way. Stay tuned.

still now news from sites.

still no news from dump’sites ***

I have a few question to those who have already sit the ICND2 640-816 exam (since September).

1. In the multi-choice questions that you got, did you have lot of questions where you were not told how many correct answers to choose.

2. Were the questions (specially ones related to routing) were from DUMPS or atleast slightly related concept wise or was it something from very deep inside WENDELL ODOMs book?? Reason I ask because I am mainly concentrating on CBT nuggets…

3. How many SIMs/Troubleshooting SIMs were there in the exam?

4. Also were there 45 questions in total and you have to answer them in 75 mins?

@Matty: Hey matty cisco does not have questions where they don’t tell you how many correct answers you need to choose so it’s straight up (choose two – choose three).
Questions about IP ROUTING are from the CCNA dumps (640-802) alot of them.
Few SIMs: – don’t remember how much but fairly easy.
There were 45 questions but I had more time because I live in a non english speaking country.
You cannot pass the exam by only relying on CBT Nuggets, you either need to practice through various dumps and/or read the wendell book which is a harsh honestly.
I think if you go through these dumps over here you will pass and lab/sims on this site.
Ironically I didn’t know about this site until the day I failed but as I’m busy working right now I’m not able to retake the exam plus I’m waiting for these sites to update their dumps.

Best of Luck.

i flunked icnd2 late august and took it again 5 days later and passed. didn’t hit many of the same questions. the sims were the same on both exams – frame relay, vyp. the sims are pretty easy. the other questions are often very tough and you need to delve deep into the books and have a really good understanding of everything. it may be easier to go down the one-exam route. icnd2 is a very tough exam. the questions are written in a ridiculous manner. they’re obviously trying to make it very hard for you to pass, even if you know your stuff.

if people want to know a time-frame, i started from scratch (not currently working as a network engineer) and passed icnd1 within 30 days, then took icnd2 less than a month later. however, i completely shut myself off from reality (no social life) and did nothing but study for the two months – including at work a lot of the time. so you can do it quickly if you apply yourself and have a lax job…

@dude

Thanks again mate…I am coming to terms now with CBT nuggets not being the complete material. However, I would like to say that the chapters not well covered by CBT are OSPF concepts and configuration, EIGRP, Frame Relay…are there any other topics you feel are not covered well bt CBT. I feel ACL, VLANs, STPs are very well covered by CBT. What do you think??

If I were you, I would look at sitting this EXAM very soon, the reason being that CISCO will most definitely phase out these old exams very soon. They have very recently upgraded CCNP and usually they try to match this timeline to CCNA. Expect a change very soon because these CCNA exams have been around for more than 3 years now….I gave my ICND 1(640-822) in March 2008 so you can imagine how long the courses have been around for 🙂

Guys seems like we are getting more and more info on the new exam…
@dude did you manage to sum up that single dump if you could ,
it would be awesome if you could post a link or email it to…let me know
and will post my email address…

And guys thanks for sharing and keeping this site so great

@Matty: np mate. Well CBT doesn’t cover OSPF & EIGRP pretty well… you are right about it.
Especially frame relay configs and shows… there’s nothing in CBT. but CBT ROX I must admit.
@s.a.ciscoguy: nope I haven’t started yet I had a tough week at work and I work at a financial institution and it’s end of the month and we are having hard times lol.
@Matty again: well I know they are gonna update but I have a feeling that they cannot do it instantly there has to be some warning or notice, I’m planing to take it november as I said.
p.s I am a former CCNA back in 2005. (things were easier back then).
all the best

@dude, Can you remember what IPv6 topics were there in the exam??. I just hate this part of the series where they do not go in deep and leave unfinished business 🙂
Any other topics you think that are not covered well in CBT ??
OSPF – I was a bit dissapointed with CBT as they do not cover concepts of multi access network like DR, BDR etc…There will be a lot of Qusestions on OSPF in the exam I believe.

Took test 2nd time and failed got an 811 i;m confused on my scoring because a section I score 76% the first time it showed i only got 38% this time and i re studied all the material before taking it this second time. Every other section i need to improve i got 100%, 91% and 86% so I’m not sure. I still have my head up and will re take soon. IP routing seems to be where I’m messing up the most I studied the 640-802 which was some of the questions on it for the exam but I’m not sure what chapter 6 it references when you look at the answers. Can any boyd help or lead me to material to study that is very helpful.
Thanks to everyone for the feedback submiited on this site.

@kellyboy – sorry for failing dude, I had bad scored on IP ROUTING aswell.
@Matty: yeah not so many questions but you must have and you don’t learn them on CBT nuggets.

@Kellyboy: I am uploading a VCE from that ccna and please let me know which ones you saw today so we can get a good dump.

@Matty: in the .vce file you can see lots of IPv6 questions and I saw some of them in the exam.

Help:
Dear Recent exam Takers
Please identify the questions you had on your exams from these two files:

http://rapidshare.com/files/417183555/AT_640-816_v1.9_september_2010.rar ( this is a pdf version)
and this .vce files I just created.
http://rapidshare.com/files/421639852/exam1.rar

anyone just paste the question number or the Screenshot or anything so I can put it in that .vce files so we can practice easier.

thnx. in advance
I’m still working myself to identify the questions but I forgot lots of them and i’m busy with work.
just let me know anything you guys recall and i’ll put that all together.

I did get 2 simulation (VTP, Frame-relay), 2 drag and drop questions I never seen before.
1 drag and drop about which subnets.

1 multi question about OSPF 3 questions about IP v6.

What is “global inside” NAT.

Where to place telnet extended acces list for telnet! You can choose between Router westcoast, Router eastcaost Fa 0/0, S0/0, inside and outside.

The IP 6 questions I remembered where What can you tell about IPv6 Uni… (with 6 possible answ.)
2000:
FE01/12 Local/global
FF00/10 Local/global
and some others answers.

The other question ipv6 was about broadcast are replaces bij multicast.

And many more.

Just got back from my ICND 2, passed barely with an 850 but ill take it. I’ve seen alot of people saying nothing on thier test was from the dumps, I took mine today and almost 75% of mine were from the dumps i had seen I used P4S 7.58 and testinside 21.24 and CBT Nuggetts and Odom. I had 1 actual sim it was a VTP sim i have seen no where pretty easy though i was given two switches and had to configure the vlan host address for one configure VTP domain and mode and even though the question did not specifically state it you need to configure trunking on the link that connected to the other switch. Also I agree with everyone else, get these concepts down as it helps cause i studied like crazy and still barely made it thru going in after just reading over alot of test dumps is a really bad idea. Also no I don’t have dumps I can send anyone for any who ask. Good luck to you all

@swansong

I guess VTP problem is below (I posted above)
VTP question, (Router – Switch 1 -Switch 2) assing gateway, IP, VTP domain, client mode

Frame-Relay
DLCI check, mapping routing (I posted above)

NAT Hot Spots (I don’t know either, I couldn’t even answer this question)
But, I am studying NAT material from starting again to better understand.

I did have the same frame relay sim today that is on the 9tut site matched it word for word and ip for ip and i believe gwbaby and i had the same VTP sim the nat hots spots were pretty simple that i had one was noticing that the inside and outside interfaces had not been assigned the other was the ACL for the public addresses was off

Guys… which frame-relay sim are you talking about?
could you post a link plz.
thnx in advance.

The frame relay sim on the 9tut site with th 3 routers N America S America and so forth going thru the cloud to the four routers in the partial mesh and you having to enter sh frame relay map and sh run to answer the following questions. My questions were same thing except i had different DLCI’s in the exam and for the password question I did have the password Tlnet configured on mine instead of no password

ahahha
You are posting comments too quickly. Slow down. – this is what I got when tried to post on this thread.

@Crono: where is that lab can you give me the link?

Hi All,

I was wondering if you can help me understand this EIGRP question from one of the dumps.
Refer to exhibit, how many paths can EIGRP routing process use to forward packets from HQ_Router to a neighbour router.

a) Two equal cost paths
b) Two unequal cost paths
c) Three equal cost paths
d) Three unequal cost paths
e) Four equal cost paths
f) Four unequal cost paths

The exhibit has the following – Its Question 60 I think in winget dump, if you just select to answer IP ROUTING questions..

I know I have seen this question but let me explain to you why.
let’s assume there are lots of equal cost paths but EIGRP can use up to 4 by default, so the answer to that question is FOUR EQUAL PATHS.
hope it helps

@Crono

Congratz Crono. The dumps you were talking about are p4s 7.58 640-802 and testinside 21.24 640-802? Have i understood well? 640-802?
So, for icnd2 exam, 75% of real questions came from those two 640-802 dumps?

@dude
What are you thinking in this moment after reading my question for Crono?
What is going on?

@Matty

Where can I find this EIGRP hot-spot problem? I saw this in the exam. I couldn’t see this from my dump collection (?) can you tell us where you have?

@ Matty

I can’t find from 9tut and Actual Test dump.

@gwbaby

The vce name where you can find the question – “http://www.examcollection.com/cisco/Cisco.CertifyMe.640-802.v2010-08-03.by.Winget.360q.vce.file.html” .

@dude

Can you have a look at the question again, because I couldn’t find any information about paths. It was showing a output from “show ip protocols command” and you have to tell by looking at the output. Also the answer was “4 unequal cost paths”. Help!!! please.

Dear exam Takers
thanks to this site and everyone on this site
I took the ICND 2 Today. I pass with score 900. The testinside 21.24 640-802 and CertifyMe.640-802.v2010-08-03.by.Winget.360q.vce covered about 75% of my exam. 25% of my exam was new questions so make sure you know your concepts if you don’t you will not pass. I use CBT nuggust and Train signal and cisco press. I had the VTP, Frame Relay sim and a ospf sim I never seen before on my exam. But as long as you understand the concepts you will pass

@Matty: Hey matty I have seen the question and it states clearly in the “show ip protocols” command that MAXIMUM PATHS ARE 4.
It states how many paths “=== CAN === ” eigrp process use, which means it doesn’t have to but it can and the only thing you need to concentrate here is look for the row where it says

Maximum Paths: 4

p.s I have to say cisco can sometimes be tricky with these questions because they put some ip addresses in there and stuff like that which makes you confused and they as something totally different.

hope it helps

@dude,

I think max paths is by default set to 4. So whenever I see a question like this, I guess it will just have to be 4 unequal cost paths….but if you look at the output it has 3 routes isnt it?? I am confused.

@Dutch,

I am planning to sit next week and nervous as hell :). Thanks for your input

@everyone,

I am repeatedy seeing this question in the dumps, to which I believe answer is incorrect. Can someone verify please –

Which of the following commands lists OSPF neighbors of interface s 0/0?

1. show ip ospf neighbor
2. show ip ospf interface
3. show ip neighbor
4. show ip interface
5. show ip ospf neighbor interface s 0/0

According to me the answer should be just 1 & 2 but the dumps say the answer as 1,2 & 5.
This is not correct because I coulddn’t get this router command to work on any of my test routers with IOS 12.3

The above 2 @Anonymous comments are from me(matty). Forgot to put my name…:)

@ Matty

Thanks for the link. I expected the OSPF that I saw from last exam, but it was not. Anyhow, thanks. I am looking for the OSPF hot spot that I saw from exam. Hopefully, it will be updated soon anywhere.

To All,

Another mistake I found in one of the DUMPS so just making the correction.
Corrected Answer for MATCH or SELECT and PLACE type question –

OSPF
– elects DR on each multi-access network

EIGRP
– is vendor specific
– Uses cost as metric
– Uses default administrative distance of 90

RIP
– Uses Hop count as metric
– Uses Bellman Ford algorithm

For some reason the answer to this question was completely mucked up in the DUMPS, hence the correction.

@Matty
first of all I see three routes but the question doesn’t ask you about the routes it asks you how many paths can EIGRP choose.. and in there you see Maximum Paths: 4
so that’s all about it nothing else .. ignore the rest.

About EIGRP AND OSPF.

OSPF:
– elects a DR on each multi-access network
– Uses Cost as Metric

EIGRP:
– is vendor specific (cisco)
– has a default administrative distance of 90

( another question is what if there are 3 possible routes to a certain destination ie. RIP, OSPF, EIGRP. the router will choose the route via EIGRP because it has lower default administrative distance comparing to outher routing protocols in this case, OSPF = 110, RIP = 120)

hope it helps

@gwbaby:
what was the hotspot that you saw on exam could you explain it a lil bit please.
thnx in advance.

@dude,

Lol..now is see another dump which says “OSPF uses cost as metric”
As far as I know OSPF uses bandwidth and EIGRP uses Bandwidth and Delay for METRIC CALCULATION.
Would this mean both EIGRP and OSPF use COST as metric?? confused..

@dude and Everybody,

CBTNUGGETS is not FULL Training resource in itself.
If you need to make sure you have had a CBT TOPIC cover everything, I suggest opening up WENDELL ODOMs book and see if all the topics marked as “KEY TOPICs” are covered.
If not and you want to avoid reading the book, download TRAINSIGNAL and they cover the theory very well.
I am a big fan of CBT NUGGETS and pay for their videos too but TRAIN SIGNAL for 640-816 goes more in-depth in theory. This is what I have found today, just by watching some videos.

Moral of the story – CBT NUGGETS + TRAIN SIGNAL..complete resource…no need to read WENDELL ODOM.

Anyone else agrees??

@dude

http://www.9tut.com/ccna-hotspot-questions

the second question is what i had word for word

@amerigo

Those are the dumps i studied and most of the ICND 2 questions i had came from there even though there were ICND1 questions

I somewhat remeber the OSPF sim everyone is talking about but not well there was a router with two links to a subnet one had to go to a t3 link and a ethernet to the route and the other just a t1 link to the route and the question was which route would be chosen another asked how many routes would show in the routing table for a router to the subnet for OSPF. Sorry i can’t be more specific than that

I agree with Matty not relying on just CBT nuggets i have never hread of train signal but im not sure about not needing odom i dont like that most of the odom examples show some basic stuff but the questions are tons harder than most exam questions i saw but the odom book provide excellent reference material.

@Matty:
To clear up your doubts about OSPF and EIGRP
OSPF: uses COST
EIGRP: uses Bandwidth & delay.
just keep these in mind and you wont be having problems kk.

@Crono: thanks mate I haven’t seen that.

@Matty again: I haven’t seen TRAINSIGNAL yet.
I like CBT but hmmm.. Wendell is really good but I dont’ like the way he sees stuff
I read Wendell only on few things I’m not sure about.

@amerigo

eigrp – Use 4 unequal cost paths
ospf – use 4 equal cost

study the trainsignal videos

I had one question something like this:

If Eigrp, Rip and OSPF is configured on router, what path will router choose to destination:

answers:
1.eigrp
2.ospf
3.rip.
4.Will chose path based on best metric

and second
I had network diagram all with OSPF routers, and question about routing table in one of them) concern how many summarized ospf network it will have. I’m searching everywhere that question because I didn’t know that.

the answer of that question is EIGRP..

note: EIGRP has a 90 AD, OSPF has a 110 AD and RIP has a 120 AD..

so it means, lower AD is must prefered path and that is EIGRP!!

@dude

OSPF and EIGRP both using BANDWIDTH..

cost is different..

cost is the value of every bandwidth of the link..

example:

10 gbps is equal to 2 cost..

correct me if im wrong..

Great website. I failed ICND2 yesterday. I felt really confident going in but got shot down. I really struggled for time. I used Wendel, Actual test and 9tut. 75% of the question in my test i had seen before. If I was a little more confident on the command line I would have stood a good chance of passing. With the preparation I had done, Familier or not I believe I could have worked the others out if I wasn’t so pushed for time. I had ICND1-Hotspots-Question 2 on this site in mine. I also had a drag and drop with a description for LMI DLCI SVC PVC DTE and DCE. I had never seen this before. I had the NAT sim. One IPv6 question which we’ve all seen on the practice tests “Which of these are valid IPv6 addresses” I need some practice on the command line can anyone point me in the right direction for a simulator with more than one interface? If I come across anything else I’ll post here.

Pass4sure have just released an update for 640-816. Is it usual/common for the others to follow? I have a subscription to actual but not pass4sure.

@ImpI
Wtf? 75% of the question in your test you saw before just using actual test dump and 9tut, ya?

Maybe you could have reached more than 75% if you used other dumps we are suggesting above.

Anyway, 75% just using AT is very interesting. Ehm AT 1.9, ya?

Every time you practice studies for ICND1 and ICND2, also examine the contents of the exam 640-802.

Passed ICND1 today with a 937. 50 questions Probably 90% were word for word from P4S v3.0.

@ImpI,

I am using real ROUTERs for practice. Some of them are old so not all commands work but you get a good understanding..
So you did no practice at all on the commands?

@all people who have passed or failed ICND 2.

Could you perhaps give a cut down (percentage) on how much was each topic worth.
For instance IPv6, VPNs, PPP, Frame Relay, OSPF, EIGRP, VTP etc etc.

I do not see an questions in relation to VPN in any of the dumps..

@ImpI

Awesome, can anyone with PASS4SURE subscription post an update..??

@Matty: I haven’t had any VPN questions when I took the exam.
I had few IPv6, PPP in wan links, framerelay ospf eigrp vtp were touched aswell.

the chapter IP routing were lots of questions.
take care

@dude,

Are you going to buy this latest Pass4sure. If yes, I am willing to contribute half…how does pass4sure work. Can both of us use it??

@dude,

Just send me your email so that we can discuss..

@dude,

When you say IP routing – do you mean VLSM, static route, OSPF, EIGRP etc.??

@Matty: exactly just know how things look like when they are broken.
show commands .. why this why that.
how would a routing table look if this if that.
smth like that but not a rocket science… u just need to get the concepts.
and as about P4S I don’t know how it works I am just waiting for a couple of days if actualtests updates it.
after all I think they are all buying from each other lol.
we’ll see someone will surely post it somewhere.
i think it’s a pdf.

@dude
Actual tests is a PDF whereas Pass4Sure is a Exam Engine.
Pass4Sure can only be activated twice so we should be ok..if you wanna proceed 🙂
I can pay you by paypal or you can pay me by paypal..how does that sound??
I am also subscribed to Actual Tests but they never respond to any emails which sucks…I have to give the exam next week

I will try it today and say is P4S valid. I think not

@Alex,

So you do have a P4s subsciption. If you do, please update us all and let us know whether we should make this investment??

hm, strange error I can’t post

Last p4s test have no update questions in compare with august when I bought it. Only test environment changed and its very poor quality with lot of mistakes in analogs of drug and drop questions and it have no explanations. So I use an earlier version of p4s.
I spoke with guy who passed from third attempt. He said that p4s is useless.

last p4s have no any new questions. Only test environment updated with lot of mistakes in analog of drug and drop questions. So i used august version of p4s, Train Signal and Net Bosson Net sim. Will see is it enough

what are you trying to post..??
If this is a P4S Dump then you will need to update it to a website like http://www.rapidshare.com or http://www.megaupload.com and post the link here.

@dude

Referring to Winget Dump. Q51 in IP ROUTING.
q. How much time will elaps before RIP route will be removed from routing table.
answer is 60 seconds …why?

no, i wrote a lot of text and it does not appear

I wrote again. Looks like some kind of filter here

ok, I will try it part by part

OK. I failed today with 784. Got 40q
VTP lab – very simple. Done fast.
Frame relay simlets. Simple to, but i doubt in 4th question.
Got drag and drop for subnets spaces. Simple.
Drag and drop NAT from here.

Only 10-12 questions from p4s dump. Last version has a lot of mistakes and NOT UPDATED.

For 10 question I have no idea how to answer. About RSTP/STP standarts and routing protocols. A lot of new drag and drops

a got 2 similar question
I know that interface with biggest IP will represent router.
So wich is bigger?
e0 – 192.168.0.1
s0 …..
loopback0 10.16.1.254
loopback1 172.10.1.1
so e0 or lo1?
How to determine biggest ip in general?