Home > New ICND1v3 Questions

New ICND1v3 Questions

October 2nd, 2017 in New Updated Questions Go to comments

Note (14th-Dec-2018): These new questions were gathered from our candidates so please learn them well before taking the ICND1 exam:

Question 1

Syslog – what does not belong?

A. host name
B. severity
C. timestamp
D. message

 

Answer: A

Question 2

What does a switch use for communication between VLANs?

A. STP
B. CDP
C. VTP
D. Etherchannel

 

Answer: C

Question 3

What is the maximum size of an Ethernet frame that uses 802.1Q tagging?

A. 1514 bytes
B. 128 bytes
C. 68 bytes
D. 1522 bytes

 

Answer: D

Question 4

When configuring a default gateway, should it be ip route 0.0.0.0…. or serial 0/0 0.0.0.0…… – dont know answer

Question 5

Which option does the route 0.0.0.0/0 represent?

A. Route with the lowest administrative distance
B. Gateway of last resort
C. Null route
D. Empty routing table

 

Answer: B

Explanation

In this question only the “Gateway of last resort” answer is suitable. A Gateway of Last Resort or Default gateway is a route used by the router when no other known route exists to transmit the IP packet. Known routes are present in the routing table. Hence, any route not known by the routing table is forwarded to the default route.

In fact this question is a bit unclear. Maybe it implies “creating a static route to network 0.0.0.0 0.0.0.0 is another way to set the gateway of last resort on a router.”

Reference: https://www.cisco.com/c/en/us/support/docs/ip/routing-information-protocol-rip/16448-default.html

Question 6

What is the purpose of a standard access list?

A. to filter traffic based on destination address
B. to deny traffic
C. to filter traffic based on source address

Answer: C

Question 7

If you are in VLAN 10 and it gets a packet from VLAN 2 with 802.1q enabled, what does it do with the packet?

A. Drops the packet
B. forwards it to VLAN 2
C. configures the port to handle traffic from VLAN 2
D. adds it to the VLAN database

Answer: A

Question 8

Drag drop question about cable types

Answer:

Coaxial <-> TV connection
Twisted <-> 10/100/1000 base
Fiber <-> BASE-5 BX
USB <-> connects two computers
Crossed-over <-> devices of the same type

Question 9

Which forwarding technology stores destination addresses in the cache?

A. MPLS
B. Cisco express forwarding
C. Process switching
D. Fast switching

 

Answer: B

Question 10

Which type of network topology requires each network node to be connected to one another?

A. Ring
B. Star
C. Mesh
D. Bus

 

Answer: C

Question 11

A router receives identical prefixes from OSPF, EIGRP, RIP and the same route is configured statically. Which route does the router use to forward traffic?

A. Static route
B. RIP route
C. EIGRP route
D. OSPF route

 

Answer: A

Question 12

Which route is the most secured : connected route

Question 13

Which syslog severity level logs informational messages?

A. 2
B. 6
C. 4
D. 0

 

Answer: B

Question 14

Which option describes a standard role that a firewall plays in an enterprise network?

A. It can permit unauthorized packets to pass to less secure segments of the network
B. It can decide which packets can traverse from a less secure segment of the network to a more secure
C. It can forward packets based on rules that are predetermined by IEEE standards
D. It can deny all packets from entering an administrative domain.

 

Answer: B

Question 15

A question with the mac table on a switch with mac 1111:1111:1111 and port 0/1 and the question was asking : You received a packet with destination mac 1111:1111:1111 on port 0/1 , how does the switch will handle the frame.

Answer: The switch forwards the frame to port 0/1 only.

Question 16

What cable use in star topology? (Choose two)

A.10 base2
B.10 base5
C.100 base2
D.100base5

Answer: 10Base-T, 100Base-T and 1000Base-T

Question 17

What is the binary of the IPv6 multicast address

Answer: 11111111

Explanation

IPv6 multicast addresses are distinguished from unicast addresses by the value of the high-order octet of the addresses: a value of 0xFF (binary 11111111) identifies an address as a multicast address; any other value identifies an address as a unicast address

Question 18

What is the lowest AD (IS-IS, IBGP, EIGRP, RIPv2 or OSPF)?

Answer: EIGRP

Explanation

The Administrative Distances (AD) of popular routing protocols is shown below:

Administrative Distances_popular_routing_protocols.jpg

Note: For IS-IS, the AD is 115; Internal BGP (IBGP) is 200

Question 19

Assume all the routing protocol have the same length prefix, what would the router prefer?

A. OSPF
B. EIGRP
C. CONNECTED
D. BGP

 

Answer: C

Question 20

In which circumstances is static routing most useful?

A. On a stub network
B. On a large network that must share routes quickly between routers
C. On a network that experiences frequent link failures
D. On a network with frequent routing changes

 

Answers: A

Question 21

Which statement describes the dynamic route correctly?

A. more secure than static
B. high scaling for large network
C. easier to configure than static route
D. build for small network

 

Answer: B

Question 22

Which statement is correct when comparing dynamic route and static route?

A. static route is more secure

Question 23

What would the router use as metrics when having different routing protocol in the routing table

A. Prefix length

Question 24

Which of the following description is correct about DNS?

A. Host will sends a request to a DNS server…

Question 25

Which statement about standard access list is true?

A. They have an implicit permit statement at the end to allow all traffic
B. They can use either a wildcard mask or a subnet mask to identify host
C. They can be identified by a number from 1 to 99
D. They must be placed close to the source of traffic

 

Answer: C

Question 26

Which of the following item is used to establish telnet session by having the host name?

A. DNS lookup
B. Ping
C. Syslog
D. ARP

Answer: A

Question 27

Which of the following command can be use to access all the files in a system?

A. syslog
B. IFS
C. ping
D. NTP

Answer: B

Question 28

For which important purpose was IPv6 addressing developed?

A. To reduce the number of public IP addresses on the internet
B. To replace network address translation
C. To remove the need for classless inter-domain routing
D. To relieve the shortage of public IP addresses on the internet

 

Answer: D

Question 29

What does the 0.0.0.0/0 mean in a routing table?

A. wildcard
B. empty routing table
C. Null table
D. Gateway of last resort

Answer: should be default route

Question 30

A host is attempting to communicate with a server from an application layer. The connection has failed, what would be the first layer to start from the troubleshooting standpoint?

A. network
B. Application
C. physical
D. session

 

Answer: C

Question 31

[am4show have=’p2;’]The left describes the types of cables, while the right describes the purposes of the cables.
Drag the items on the left to the proper locations. (Not all items can be used.)

Cable_Types.jpg

Answer:

+ switch access port to router: straight-through
+ switch to switch: crossover
+ PC COM to switch Console port: rollover[/am4show]

Explanation

To remember which type of cable you should use, follow these tips:

– To connect two serial interfaces of 2 routers we use serial cable
– To specify when we use crossover cable or straight-through cable, we should remember:
Group 1: Router, Host, Server
Group 2: Hub, Switch
One device in group 1 + One device in group 2: use straight-through cable
Two devices in the same group: use crossover cable

For example: we use straight-through cable to connect switch to router, switch to host, hub to host, hub to server… and we use crossover cable to connect switch to switch, switch to hub, router to router, host to host… )

Question 32

Which destination IP address can a host use to send one message to multiple devices across …?

A. 239.255.0.1
B. 172.20.1.0
C. 192.168.0.119
D. 127.0.0.1

 

Answer: A (multicast address)

Question 33

Which value is of primary importance when a router populates its routing table for unique routes?

A. Administrative distance
B. Prefix length
C. Network address
D. Metric

 

Answer: A

Explanation

Making a forwarding decision actually consists of three sets of processes: the routing protocols, the routing table, and the actual process which makes a forwarding decision and switches packets. The longest prefix match always wins among the routes actually installed in the routing table, while the routing protocol with the lowest administrative distance always wins when installing routes into the routing table.

routing_process.gifReference: http://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol-eigrp/8651-21.html

Question 34

Which IPv6 address type is a public address?

A. Global unicast
B. Multicast
C. Link local
D. Unique-local

 

Answer: A

Question 35

How is the MAC address table of a switch populated?

A. When the switch receives an Ethernet frame with a new destination MAC address, it installs the destination MAC address and the ingress switch port in the MAC address table
B. When the switch receives an Ethernet frame with a new source MAC address, it installs the source MAC address and the ingress switch port in the MAC address table
C. When the switch receives an Ethernet frame with a new destination MAC address, it installs the destination MAC address and the egress switch port in the MAC address table
D. When the switch receives an Ethernet frame in which the source and destination MAC address are new, it installs the destination MAC address and the ingress switch port in the MAC address table

 

Answer: B

Explanation

A switch only learns (populates) its MAC address table with source MAC addresses only.

Question 36

Which statement describes the effect of exec-timeout 30 command?

A. The router disconnects the user session if it is inactive for 30 minutes
B. The router maintains a user session indefinitely after it is active for 30 mins
C. The router disconnects a user session if it is inactive for 30 seconds
D. The router maintains a user session indefinitely after it is active for 30 seconds.

 

Answer: A

Explanation

The “exec-timeout” command is used to configure the inactive session timeout on the console port or the virtual terminal. The syntax of this command is:

exec-timeout minutes [seconds]

Therefore we need to use the “exec-timeout 30” command to set the user inactivity timer to 30 minutes. To set the user inactivity timer to 30 seconds we use the “exec-timeout 0 30”.

Question 37

Which statement is true about port-security violations is true?

A. When a violation occurs on a switch port in restrict mode, the switch port continues to accept traffic from unknown MAC address until the administrator manually disables it.
B. When a violation occurs on a switch port in protect mode, it sends a syslog notification message
C. A port In the err-disabled state must be re-enabled manually, if recovery is disabled
D. When a switch port is in protect mode, it allows traffic from unknown MAC address until it has learned the maximum allowable number of MAC addresses

 

Answer: C

Question 38

Which statement is true about static and dynamic routing is true?

A. Only static routes are shared between connected interfaces
B. Dynamic routing is more scalable than static routing
C. Only dynamic routes are secure
D. Static routing is easier to maintain in a large network than dynamic routing.

 

Answer: B

Question 39

Which metric or metrics does RIP use to determine the routing table metric for a route?

A. Bandwidth and delay
B. Hop count
C. Bandwidth and hop count
D. Bandwidth

 

Answer: B

Question 40

Which network configuration allows a switch to send traffic from multiple VLANS over a single link to a router that routes between the VLANs?

A. Port channel
B. Router-on-a-stick
C. Virtual trunking
D. Spanning-tree

 

Answer: B

Question 41

Which statement about native VLAN traffic over 802.1Q trunk is true?

A. It is discarded by STP
B. It is placed is a high-priority queue
C. It is tagged with a value of 1
D. It is untagged

 

Answer: D

Question 42

Which feature allows a device to use a switch port that is configured for half-duplex to access the network?

A. Split horizon
B. CSMA/CD
C. IGMP
D. Port security

 

Answer: B

Explanation

CSMA/CD stands for Carrier Sense Multiple Access with Collision Detection. In an Ethernet LAN, before transmitting, a computer first listens to the network media. If the media is idle, the computer sends its data. If the media is not idle (another station is talking), the computer must wait for some time.

When a station transmits, the signal is referred to as a carrier. Carrier Sense means that before a station can send data onto an Ethernet wire, it have to listen to see if another “carrier” (of another station) is present. If another station is talking, this station will wait until there is no carrier present.

Multiple Access means that stations can access the network at any time. It is opposed to Token-Ring network where a station must have the “token” so that it can send data.

In short, CSMA/CD is the technology used for half-duplex switch port to transmit. CSMA/CD is not necessary for full-duplex switch port.

Question 43

Refer to the exhibit.

<exhibit missing>

If switch-A receives a frame with destination MAC address 0000.0000.0001 on its Fa0/1 interface, how does it process the frame?

A. It forwards the frame back out of interface Fa0/1
B. It floods the frame to all interfaces except Fa0/1
C. It holds the packet until the MAC address timer expires and then drops the frame
D. It drops the frame immediately

 

Answer: maybe B

Explanation

As the exhibit is missing so we can only guess. But B is the most suitable answer in all cases. If the MAC address 0000.0000.0001 is new to the switch (this MAC have not existed in the MAC address table) then surely the answer is B.

Question 44

When a router makes a routing decision for a packet that is received from one network and destined to another, which portion of the packet does it replace?

A. Layer 4 protocol
B. Layer 3 IP address
C. Layer 2 frame header and trailer
D. Layer 5 session

 

Answer: C

Explanation

During the transmission of a packet from source to destination, only Layer 2 information is replaced in the path. Layer 3 information remains the same (except when NAT is used).

Question 45

Which protocol can identify connected devices within a mixed-vendor infrastructure?

A. Virtual terminal protocol
B. Network time protocol
C. Link level discovery protocol
D. Cisco discovery protocol

 

Answer: C

Question 46

Which interface configuration is used with a router-on-a-stick configuration?

A. VRF
B. Subinterfaces
C. PIM sparse mode
D. Passive-interface

 

Answer: B

Question 47

You have configured the host computers on a campus LAN to receive their DHCP addresses from the local router to be able to browse their corporate site. Which statement about the network environment is true?

A. Two host computers may be assigned manually on each host
B. The DNS server must be configured manually on each host
C. It supports a DNS server for use by DHCP clients
D. The domain name must be configured locally on each host computer

 

Answer: C

Explanation

DHCP supports configuring a domain name to assign to the DHCP clients. For example:

Router(config)#ip dhcp pool CLIENTS
Router(dhcp-config)#domain-name 9tut.com

Question 48

Where is private IPv4 addressing used?

A. On the endpoints of a VPN tunnel that traverses outside an administrator domain
B. At a remote site that connects over public infrastructure to a hub
C. Within an enterprise
D. Over the internet

 

Answer: C

Question 49

Which protocol allows VLANs to be dynamically configured between multiple switches?

A. IGMP
B. STP
C. VTP
D. 802.1Q

 

Answer: C

Question 50

Client A cannot reach client B by its hostname. Which reason for the problem is most likely true?

A. The connected router is using the default domain lookup configuration
B. The hostname for client B is missing from the connected router
C. A DNS server has been misconfigured
D. Telnet has been disabled on the connected router.

 

Answer: C

Question 51

Which first step must a client perform to connect to an internal host when the hostname is known, but the IP address is unknown?

A. The client sends the host name in a DNS reply to a DNS server, and the DNS server responds with the host IP address
B. The client exchanges IP address information with a DNS server on the same LAN
C. The client looks up the hostname in the ARP table to determine the IP address
D. The client sends the host name in a DNS request to a DNS server, and the DNS server responds with the host IP address.

 

Answer: D

Explanation

When a client knew about the hostname but not the IP address, it needs to resolve the hostname to the IP address by sending a DNS request to its DNS server.

Notice that the ARP table is responsible for resolving IP address to MAC address only. It has nothing to do with the hostname.

==================New Questions added on 9th-Dec-2017==================

Question 52

Which route option can be used to back-up in case of fail?

Answer: floating route

Question 53

Which of the following is true about TCP and UDP?

Answer: only TCP order the transmission packets

Question 54

If a switch received a frame while forwarding others, how frame would be handled?

A. It will interrupt the frames
B. The switch will put the frame in a queue
C. Will be forwarded at the same time with the current frame
D. The new frame will forward first

 

Answer: C

Question 55

Which of the following true about access point?

A. It used physically to connect network devices
B. It is used as a router
C. Provide full duplex communication
D. It is a layer 2 device used to extend the LAN coverage to wireless devices

 

Answer: D

Question 56

Which of the following used to identify immediate destination?

A. Administrative distance
B. Metric
C. Next hop
D. Destination network

 

Answer: C

Question 57

Which of the following options could be used on router to prevent reassign IP address statically?

A. Pool
B. Lease
C. Client ID
D. Exclude address

 

Answer: D

Question 58

A router with a default setting deployed, how will act if it received mistype command?

A. Disable DNS look up
B. Recognizing the command
C. Try to resolve the command to an IP address
D. Try to correct the command
E. Show error message

 

Answer: C

Question 59

Which symbol ping of the following is for unknown packet?

A. .
B. *
C. ?
D. U

 

Answer: C

Explanation

The table below lists the possible output characters from the ping facility:

Character Description
! Each exclamation point indicates receipt of a reply.
. Each period indicates the network server timed out while waiting for a reply.
U A destination unreachable error PDU was received.
Q Source quench (destination too busy).
M Could not fragment.
? Unknown packet type.
& Packet lifetime exceeded.

Reference: https://www.cisco.com/c/en/us/support/docs/ios-nx-os-software/ios-software-releases-121-mainline/12778-ping-traceroute.html

Question 60

Which cables could be used for star topology? (Choose two)

A. 10 Base T
B. 100 Base T
C. 10 Base 5
D. 10 Base 2

 

Answer: A B

Question 61

Which of the following is true about dynamic route?

A. Reduce CPU of the network
B. More secure than static
C. Complicate the maintenance
D. Allow fast convergence when fail happen

 

Answer: D

Question 62

What RIPv2 use to elect of route?

A. Hop count
B. Administrative distance
C. Bandwidth

 

Answer: A

Question 63

Which of the following are two local host characters?

A. 32/prefix
B. 255.255.255.0
C. The administrative distance is 0
D. Dynamically learned
E. ?

 

Answer: A C

Question 64

Which attributes change all the path way (Choose two)

A. MAC destination address
B. MAC destination address
C. IP Source address
D. IP Source address

 

Answer: A B

Question 65

Why a host uses DNS server?

A. DNS client request to server
B. To resolve IP to FQDN
C. To resolve FQDN to IP
D. Assign IP

 

Answer: C

FQDN (Fully Qualified Domain Name)
E. Verify connection

==================New Questions added on 9th-Aug-2018==================

Question 66

What time zone is set by default on the router?

A. GMT
B. UMT

 

Answer: A

Explanation

By default, the router uses UTC, also called Coordinated Universal Time. UTC, formerly known as Greenwich Mean Time (GMT), has become the worldwide standard for time and date.

 

Comments (100) Comments
Comment pages
1 2 3 4 897
  1. SI
    October 5th, 2017

    I took the ICND 1 exam on 25th Sept and passed.I got 50% qts out of 9tut. most of them are the ones above in new qts. Studied 9tut as well as todd lamlee qts/ few other dump sites.Need to know the concepts very well.
    sim were security and dhcp similar to this but one from vce dumps posted in earlier thread.

  2. Gurpreet
    October 13th, 2017

    I can only see 15 questions under “ICNDV3 new question”. Are there any new dumps? or this is it. I am a premium member

  3. Areste
    October 16th, 2017

    Hi guys
    any new dumps ? I’m going to pass the exam on Saturday.
    Thanks

  4. AJ
    October 17th, 2017

    hi, can someone confirm that the old questions are no longer valid? how many from them actully will appear in the exam?
    and what about the labs?

  5. aces
    October 18th, 2017

    @AJ

    9tut have specifically made this new question column to confirm that the old questions are invalid or aren’t worth studying anymore.

  6. Kryptonian
    October 18th, 2017

    How valid are these new questions.??
    Questions from ICND1 arent valid as per 9tut.

    How about ICND2 .. ?

  7. DS
    October 19th, 2017

    Are ICND2 questions also changed 9tut?

  8. Anonymous
    October 19th, 2017

    Hi

    can someone give his opinion about this question/answer ?

    What cable use in star topology? (Choose two)

    A.10 base2
    B.10 base5
    C.100 base2
    D.100base5

    Answer: 10Base-T, 100Base-T and 1000Base-T

    I think the meaning of the answers is that cooper cables are tipically used for access topology, so that’s the best answer.

  9. AJ
    October 21st, 2017

    @aces i get that, but how sure they are that the old questions are invalid??

    and what about the labs?

  10. RW
    October 24th, 2017

    Is there any time table on when the ICND1 Q&A’s will be updated for prepping for the test. I hate spending money on something that’s not up to date.

  11. AL
    October 24th, 2017

    Are the ICND2 questions still valid?

  12. NastyAL
    October 25th, 2017

    Passed my CCENT today. Majority of my questions in the composite test, along with the DHCP sim. Only only one or two questions from the “new” questions. Thanks everyone for your help. Safari Books Online + 9tut is a great combo.

  13. sharminnie
    October 25th, 2017

    can anyone please send me any new dumps they might have? Giving my exam soon 😀 sharmynkayani1 at gmail

  14. sharminnie
    October 25th, 2017

    can anyone confirm whether studying the old questions is not valid?

  15. Jamal
    October 25th, 2017

    Passed CCENT today, there was a mix of old and new questions. Also the sims are slightly different so you do have to know what you’re doing.

  16. NastyAL
    October 25th, 2017

    @sharminnie Definitely study the old questions.

  17. sharminnie
    October 26th, 2017

    @NastyAL so going through the questions on 9tut and Jolie should be good and help pass? 🙂 Also summarising and going through the book.

  18. chico
    October 27th, 2017

    Any questions about ospf basics?

  19. Anonymous
    October 27th, 2017

    Taken and passed. Material provided by 9tut is plenty if one has basic understanding of concepts covered. Saw DHCP and security testlet sims.

  20. Prof
    October 27th, 2017

    Hi, just to updste u, i did icnd1 exam today and failed with a score of 799. The updated version 3 with majority of the 18 questions where there. I got dhcp simulator which has been changed. Thats the point i failed the most. Others where 70 and 80%. Does anyone have the most recent dumps on the dhcp simulator or can remember the questions on it… This is my 2nd attempt. Any help will be appreciated.
    Many thanks.

  21. Prof
    October 27th, 2017

    Hi anonymous, can u help with the dhcp simlets? Thanks

  22. drumpf
    October 28th, 2017

    Just passed icnd1 today. The questions on the exam are slightly different than the ones here, so you need to know why the answers are what they are. I’m not sure memorizing will get you through. The exam sims have different IP’s and addressing schemes too.

  23. NastyAL
    October 30th, 2017

    @sharminnie Sorry for the delay, if you use just 9tut questions I’d say it is a 50/50 chance of passing. I highly suggest other study material as well. I spent 3 weeks watching CCENT videos on Safaribooksonline then a day and half here studying.

  24. Nyala
    November 2nd, 2017

    There was a question On the ICND1 Like,
    what is the administrative distance of connected routes?
    A.1 B. 0 C. 10 D. 90
    Answer is B

  25. 9tut
    November 2nd, 2017

    @Nyala: Thanks for your information. We added this question to https://www.9tut.net/icnd1-100-105/icnd1-ip-routing-4

  26. Cris
    November 4th, 2017

    In my exame a saw a question about the function of the Access Point, like definition and your purpose.

  27. Cris
    November 4th, 2017

    9 tut questions are still valid. The fundamentals are here.

  28. Goldenstein
    November 10th, 2017

    Hello, I finally passed the ICND1 with the score of 951/1000. The 2nd attempt was definitely harder than the 1st attempt in my opinion.

    95% of the 1st attempt questions can be found on 9tut, my 2nd attempt was about 70%…still this site is awesome! 9tut saved me!

    For those who are asking about Jodie’s dump…don’t worry about it, just know the material well enough and use the 9tut questions and you will be just fine. The hands on questions were almost identical, however the answers are slightly different.

    I remembered a few new questions, I will be posting them tomorrow.

    Feel free to ask me any question while my memory is still fresh.

  29. James
    November 10th, 2017

    Congratulations Goldenstein, did they repeat some of the questions from your first attemp and would you please post what you can remember from the last test. Thanks in advance,

  30. SYNC_ACK
    November 11th, 2017

    Congrats Goldenstein!!! I’m going for my 2nd attempt on this coming Monday so any additional advice would be greatly appreciated. Do you remember exactly which labs/hands-on questions came up? Definitely want to max out the points this time.

  31. Goldenstein
    November 11th, 2017

    @9tut: Here are some new questions… I don’t quite know the answer of these questions so you guys might have to look into it.

    @James: Yes, for a few. All the questions above on this page showed up on my 1st and 2nd attempt. I will answer more question if you got more.

    @SYNC_ACK: Security Testlet Simulator and Show Configuration Simulator are both on there. The questions were exactly the same, but the answers are different… because the running-config of the topology are slightly different. Don’t worry about it tho, it’s still easy. They made it even more obvious in my opinion. When in doubt, use cross elimination method.

    1.Which of the following item is used to establish telent session by having the IP address and host name?

    A. DNS loopup
    B. Ping
    C. Syslog
    D. ARP

    This was a VERY tricky question. I pick B as the closest answer, I could be wrong.

    2.Which of the following command can be use to access all the files in a system?

    A. syslog
    B. IFS
    C. ping
    D. NTP

    Not sure what the answer is for this one either.

    3.What is reason behind the invention of ipv6?

    A. Relieve the shortage of ipv4
    B. Replace Network Address Translation
    C. ….

    I think it’s A.

    4.What does the 0.0.0.0/0 mean in a routing table?

    A. wildcard
    B. empty routing table
    C. Null table
    D.gateway of last resort

    Not sure about this one

    5. A host is attempting to communicate with a server from an application layer. The connection has failed, what would be the first layer to start from the troubleshooting standpoint?

    A. network
    B. Application
    C. physical
    D. session

    Pretty sure the answer is C. Physical. You wanna check layer 1 first

    There are a few more that I could probably remember from various topic, feel free to ping me via topic header so I could remember more.

  32. Anonymous
    November 11th, 2017

    Hello Goldenstein,
    thank you very much for your input, and good luck with ICND2
    for question 4
    The default route in Internet Protocol Version 4 (IPv4) is designated as the zero-address 0.0.0.0/0 in CIDR notation, often called the quad-zero route. … A route lookup that does not match any other route, falls back to this route. Based on this the answer is
    D.gateway of last resort.

  33. Anonymous
    November 11th, 2017

    How about NAT and IPV6?

  34. Anonymous
    November 11th, 2017

    Why did you choose B.Ping for the 1st Question?

  35. James
    November 11th, 2017

    Also for
    2.Which of the following command can be use to access all the files in a system?
    A. syslog
    B. IFS
    C. ping
    D. NTP
    The answer is
    B. IFS which is Cisco IOS File System (IFS) Commands

  36. Goldenstein
    November 11th, 2017

    @Anonymous: I don’t know, I could be wrong.

    @James: oh good, maybe I chose the right answer.

  37. James
    November 11th, 2017

    Cisco has created a file system called Cisco IFS that allows you to work with files and directories
    just as you would from a Windows DOS prompt. The commands you use are dir, copy,
    more, delete, erase or format, cd and pwd, and mkdir and rmdir.

  38. James
    November 11th, 2017

    @Goldenstein do you think option A. was DNS lookup because that might be the answer?
    1.Which of the following item is used to establish telent session by having the IP address and host name?
    A. DNS loopup
    B. Ping
    C. Syslog
    D. ARP

  39. Goldenstein
    November 11th, 2017

    @9tut:Here’s more new question…

    1. Assume all the routing protocol have the same length prefix, what would the router prefer?

    A. OSPF
    B. EIGRP
    C. CONNECTED
    D. BGP

    2. What circumstance is best for static route?

    A. Implementation for large scale network
    B. easier for convergence when experiencing link failure
    C. a topology where route changes are very frequent
    D. easier to configured…..

    3. which statement describes the dynamic route correctly?

    A. more secure than dynamic
    B. high scaling for large network
    C. easier to configure than static route
    D. build for small network

    4. which statement is correct when comparing dynamic route and static route?

    A. static route is more secure

    5. what would the router use as metrics when having different routing protocol in the routing table

    A. Prefix length

    6. Which of the following description is correct about DNS?

    A. Host will sends a request to a DNS server…

    7. Which of the following statement is correct regarding to standard access list?

    A. Range is 1-99

  40. 9tut
    November 11th, 2017

    @Goldenstein: Thank you very much. We have just updated them to the new ICND1v3 Questions.

  41. Goldenstein
    November 11th, 2017

    @9tut: here are more that I could remember…

    Which of the following statement is correct regarding to Ethernet frame when the destination address is unknown?

    A. It will be send out as a layer 3 broadcast
    B. Frame will be drop
    C. Source address will be saved and ingress out to all ports
    D. Destination address will be saved and egress out to all ports

    Which of the following item provide as a redundant link in case of route failure?

    A. floating static route

  42. James
    November 12th, 2017

    Goldenstein: you’re the man

  43. SS
    November 12th, 2017

    Passed the ICND1 today. Used all of the 9tut questions, “31 Days Before Your CCENT” book, CBT Nuggets Videos + CBT Nuggets Transcender exams. I’d say all of these sources had some of the new ICND1 questions but the CBT nuggets Transcender practice exams really helped.

  44. SS
    November 12th, 2017

    @Goldenstein:

    The Cisco Routing and Switching Fundamentals book states that:

    “A default static route is a route that matches all packets. A default route identifies the gateway IP address to which the router sends all IP packets that it does not have a learned or static route. A default static route is simply a static route with 0.0.0.0/0 as the destination IPv4 address. Configuring a default static route creates a Gateway of Last Resort.”

    So,

    4.What does the 0.0.0.0/0 mean in a routing table?
    A. wildcard
    B. empty routing table
    C. Null table
    D.gateway of last resort

    Should be D?

  45. Goldenstein
    November 12th, 2017

    @SS: Yeah maybe, that’s the one I picked.

  46. Speedy
    November 12th, 2017

    I passed ICDN1 today , some of questions were new , below are some of what remember

    1- which technology store destination address in the cache ?
    Cisco Express Forwarding

    2- What does the 0.0.0.0/0 mean in a routing table ?
    gateway of last resort

    3- which IP address is in the same subnet of 192.168.161.10/19
    192.168.160.1

    4- Which of the following item is used to establish telent session by having the IP address and host name?
    DNS loopup

    5- Which of the following command can be use to access all the files in a system?
    IFS

    The DHCP scenario was in the exam, but the configuration on the routers where different
    so make sure to check the configuration before answering even if the questions were the same but the answer will be different

  47. James
    November 13th, 2017

    Congratulations Speedy, do you remember the ACL questions?

  48. Speedy
    November 13th, 2017

    James , if you are referring to ACL questions in DHCP scenario then it the same exact questions as in 9tut, but the answer is different due different router configuration.

  49. diver214
    November 15th, 2017

    Please help out with dumps for INCD1 and INCD2 please send at diver214 at yahoo.com

  50. FlashMemory
    November 15th, 2017

    Thanks everyone for update, I’m taking my exams on 17th November, any additional materials,

  51. PuppyMonkey
    November 16th, 2017

    Just passed INCD1 today with a 904. Most of the questions on the test were from here. Pretty sure I saw all the questions posted above. I had the DHCP and Security sims but with different answers and the cable type drag and drop.

  52. Pete
    November 17th, 2017

    Hi! Can anybody explain the following?

    4- Which of the following item is used to establish telnet session by having the IP address and host name? DNS lookup

    How can you establish a telnet session this way? If you have the IP address, what is the need for the host name? It would make sense if only the hostname was provided and then by using nslookup you will resolve the IP address associated….

  53. PuppyMonkey
    November 17th, 2017

    Pete, I had that question on my test. I dont remember exactly how it is worded on the test but what is post here is close but not correct. The DNS lookup is the right answer though.

  54. James
    November 18th, 2017

    Pete, you are right but look at the other answers, DNS lookup is the closest one to be correct.

  55. Pete
    November 18th, 2017

    Hi James and PuppyMonkey, yes by discarding I would choose that one as well!

  56. Areste
    November 19th, 2017

    Hi guys, exam achieved yesterday with 932/1000, so happy 🙂 Thanks a lot to everyone, most of questions are in this section as well as in 9tut. Definitely this website is still valid.
    In DHCP simulator they changed the DHCP pool configuration, for NTP question they omitted the ntp master command in R2.
    About the following question :
    4- Which of the following item is used to establish telnet session by having the IP address and host name?

    In the exam the IP address was not mentionned, only the host name was, so definitely the correct answer is “DNS lookup”.

    There was a question about firewall, something like this :
    What can you do with a firewall ?
    — decide to authorize some packets from a less secure zone to a more secure zone

    Next step ICND2.

  57. Pete
    November 19th, 2017

    Hi ICND1. These are the mistakes in my opinion:

    How is the MAC address table of a switch populated?
    A. When the switch receives an Ethernet frame with a new destination MAC address, it installs the destination MAC address and the ingress switch port in the MAC address table
    B. When the switch receives an Ethernet frame with a new source MAC address, it installs the source MAC address and the ingress switch port in the MAC address table
    C. When the switch receives an Ethernet frame with a new destination MAC address, it installs the destination MAC address and the egress switch port in the MAC address table
    D. When the switch receives an Ethernet frame in which the source and destination MAC address are new, it installs the destination MAC address and the ingress switch port in the MAC address table

    Answer: I would say B

    Which RFC was created to alleviate the depletion of IPv4 public address?
    A. RFC 1519
    B. RFC 1918
    C. RFC4193
    D. RFC 1518

    Answer: D

    You have configured the host computers on a campus LAN to receive their DHCP addresses from the local router to be able to browse their corporate site. Which statement about the network environment is true?
    A. Two host computers may be assigned manually on each host
    B. The DNS server must be configured manually on each host
    C. It supports a DNS server for use by DHCP clients
    D. The domain name must be configured locally on each host computer

    Answer: C

    ———————
    Which MTU size can cause a baby giant error?
    A. 9216
    B. 1500
    C. 1600
    D. 1518

    Answer: D

    ——————

    Which first step must a client perform to connect to an internal host when the hostname is known, but the IP address is unknown?
    A. The client sends the host name in a DNS reply to a DNS server, and the DNS server responds with the host IP address
    B. The client exchanges IP address information with a DNS server on the same LAN
    C. The client looks up the hostname in the ARP table to determine the IP address
    D. The client sends the host name in a DNS request to a DNS server, and the DNS server responds with the host IP address

    Answer D

    —————–

    Hope it helps!

  58. Pete
    November 19th, 2017

    Sorry:

    How is the MAC address table of a switch populated?

    B and C

  59. Pete
    November 19th, 2017

    How is the MAC address table of a switch populated?
    B and C(only if two answers needed). Since the switch, when MAC destination is unknown, will flood the frame out of all ports to figure out the port….

    If only one answer I would go for B, I would choose C as well only if 2 answers are needed.

    @9tut, could you clarify it? Thank you

  60. 9tut
    November 20th, 2017

    @Pete: We have just reviewed and updated the answers of some questions with explanation. Kindly check them again!

  61. James
    November 21st, 2017

    Hello Pete, would you please tell me what you remember about the DHCP question?

  62. Pete
    November 21st, 2017

    Hi James, I haven´t done the exam yet…

  63. sam
    November 22nd, 2017

    hey guys, just a little update, took the exam today and I was only one question away to pass, most of the question from the once posted above so I’m just gonna post the new questions

    1. Which route option can be used to back-up in case of fail?
    Answer: floating route

    2. Which of the following is true about TCP and UDP?
    Answer: only TCP order the transmission packets

    3. If a switch received a frame while forwarding others, how frame would be handled?
    A. It will interrupt the frames
    B. The switch will put the frame in a queue
    C. Will be forwarded at the same time with the current frame
    D. The new frame will forward first

    4. Which of the following true about access point?
    A. it used physically to connect network devices
    B. it’s used as a router
    C. provide full duplex communication
    D. it’s layer 2 device used to extend the LAN coverage

    5. which of the following used to identify immediate destination?
    A. Administrative distance
    B. Metric
    C. Next hope
    D. Destination network

    6. Which of the following options could be used on router to prevent reassign IP address statically?
    A. Pool
    B. Lease
    C. Client ID
    D. Exclude address

    7. A router with a default setting deployed, how will act if it received mistype command?
    A. Disable DNSlook up
    B. Recognizing the command
    C. Try to resolve the command
    D. Try to correct the command
    E. show error message

    8. Which symbol ping of the following is for unknown packet?
    A. .
    B. *
    C. ?
    D. U

    9. Which cables could be used for star topology? (choose two)
    A. 10 Base T
    B. 100 Base T
    C. 10 Base 5
    D. 10 Base 2

    10. Which of the following true about dynamic route?
    A. Reduce CPU of the network
    B. More secure than static
    C. Complicate the maintenance
    D. Allow fast convergence when fail happen

    11. What RIPv2 use to elect of route?
    A. Hope count
    B. Administrative distance
    C. Bandwidth
    D. ……

    12. Which of the following are two local host characters?
    A. 32/prefix
    B. 255.255.255.0
    C. The administrative distance is 0
    D. Dynamically learned
    E. Routing table

    13. Which attributes change all the path way (choose two)
    A. MAC destination address
    B. MAC destination address
    C. IP Source address
    D. IP Source address

    14. Question asking when the host sending request ………..
    A. DNS client request to server
    B. To resolve IP to FQDN
    C. To resolve FQDN to IP
    D. Assign IP
    E. Verify connection

    15. Which request used to resolve …….
    A. Send DNS request to DNS server
    B. Send DNS request to DHCP server
    C. …….

    sorry about the last two questions cant remember how did they exactly wrote the questions!
    @9tut would you certify please !!

  64. sharkguy
    November 22nd, 2017

    I wish I found this site last week, I took my test yesterday and got a 799, so close!!!! Yet so far!! I will say that these questions are exactly what was on my test. I only got 2 wrong that I see and can remember. There was one question about a cisco switch and cisco ip phone about tagging but I can not remember the whole wording. Also there was a question about switch port security and learning the max number of Mac address. Sorry I can’t remember the questions. 15th is the new date, hopefully with browsing this site and some others I can get the little edge I need.

  65. Sunil
    November 25th, 2017

    Hi All ,
    Thanks for posting new question ,Please keep posting new question its is very helpful .

  66. Omar
    November 26th, 2017

    hi guys thanks for posting new questions

    i really confused about this question
    What cable use in star topology? (Choose two)

    A.10 base2
    B.10 base5
    C.100 base2
    D.100base5

    Answer: 10Base-T, 100Base-T and 1000Base-T

    is it a,c or b,d

  67. Sunil
    November 26th, 2017

    Hi 9tut ,

    Request you to please answer these following questions .

    1. Which route option can be used to back-up in case of fail?
    Answer: floating route
    2. Which of the following is true about TCP and UDP?
    Answer: only TCP order the transmission packets
    3. If a switch received a frame while forwarding others, how frame would be handled?
    A. It will interrupt the frames
    B. The switch will put the frame in a queue
    C. Will be forwarded at the same time with the current frame
    D. The new frame will forward first
    4. Which of the following true about access point?
    A. it used physically to connect network devices
    B. it’s used as a router
    C. provide full duplex communication
    D. it’s layer 2 device used to extend the LAN coverage
    5. which of the following used to identify immediate destination?
    A. Administrative distance
    B. Metric
    C. Next hope
    D. Destination network
    6. Which of the following options could be used on router to prevent reassign IP address statically?
    A. Pool
    B. Lease
    C. Client ID
    D. Exclude address
    7. A router with a default setting deployed, how will act if it received mistype command?
    A. Disable DNSlook up
    B. Recognizing the command
    C. Try to resolve the command
    D. Try to correct the command
    E. show error message
    8. Which symbol ping of the following is for unknown packet?
    A. .
    B. *
    C. ?
    D. U
    9. Which cables could be used for star topology? (choose two)
    A. 10 Base T
    B. 100 Base T
    C. 10 Base 5
    D. 10 Base 2
    10. Which of the following true about dynamic route?
    A. Reduce CPU of the network
    B. More secure than static
    C. Complicate the maintenance
    D. Allow fast convergence when fail happen
    11. What RIPv2 use to elect of route?
    A. Hope count
    B. Administrative distance
    C. Bandwidth
    D. ……
    12. Which of the following are two local host characters?
    A. 32/prefix
    B. 255.255.255.0
    C. The administrative distance is 0
    D. Dynamically learned
    E. Routing table
    13. Which attributes change all the path way (choose two)
    A. MAC destination address
    B. MAC destination address
    C. IP Source address
    D. IP Source address
    14. Question asking when the host sending request ………..
    A. DNS client request to server
    B. To resolve IP to FQDN
    C. To resolve FQDN to IP
    D. Assign IP
    E. Verify connection
    15. Which request used to resolve …….
    A. Send DNS request to DNS server
    B. Send DNS request to DHCP server
    C. …….

  68. FlashMemory
    November 27th, 2017

    Hi Omar/Sunil
    Concentrate on Destination and Topology line, I hope its helps.

    Designation, Supported Media , Maximum Segment Length, Transfer Speed, Topology
    10Base-5 Coaxial 500m 10Mbps Bus
    10Base-2 Thin Coalxial (RG-58 A/U) 185m 10Mbps Bus

    10Base-T Category3 (UTP) 100m 10Mbps Star,

    100Base-T Category5 UTP 100m 100Mbps Star,

  69. FlashMemory
    November 27th, 2017

    10Base-5 ——for Bus Topology
    10Base-2 ——for Bus Topology
    10Base-T ——Star Topology,
    100Base-T ——-Star Topology,

    What cable use in star topology? (Choose two)
    A.10 base2 ….. .for Bus Topology
    B.10 base5…. for Bus Topology
    C.100 base2…..,
    D.100base5…….Star Topology,

    9. Which cables could be used for star topology? (choose two)
    A. 10 Base T……..Star Topology
    B. 100 Base T……Star Topology
    C. 10 Base 5
    D. 10 Base 2

    I hope its answer both questions

  70. afm
    November 27th, 2017

    hi 9Tut please help with the 15 answers Sam asked above, i wrote on the 24th November 2017 and received all the questions above as he asked.
    also failed by 30marks.

  71. Sunil kumar
    November 28th, 2017

    Hi ,9tut ,
    Request you to please help to resolve the above questions .

  72. Just passed ICND1 today 930 points
    November 28th, 2017

    @Sunil

    Most of your questions were in my exam today. Beware, some of my answers could be wrong.

    1. Which route option can be used to back-up in case of fail?
    Answer: floating route
    I picked this answer as floating route

    2. Which of the following is true about TCP and UDP?
    Answer: only TCP order the transmission packets
    I picked this answer as well
    3. If a switch received a frame while forwarding others, how frame would be handled?
    A. It will interrupt the frames
    B. The switch will put the frame in a queue
    C. Will be forwarded at the same time with the current frame
    D. The new frame will forward first
    I picked C
    4. Which of the following true about access point?
    A. it used physically to connect network devices
    B. it’s used as a router
    C. provide full duplex communication
    D. it’s layer 2 device used to extend the LAN coverage to wireless devices
    I picked D

    5. which of the following used to identify immediate destination?
    A. Administrative distance
    B. Metric
    C. Next hope
    D. Destination network
    I picked D
    6. Which of the following options could be used on router to prevent reassign IP address statically?
    A. Pool
    B. Lease
    C. Client ID
    D. Exclude address
    I picked D
    7. A router with a default setting deployed, how will act if it received mistype command?
    A. Disable DNSlook up
    B. Recognizing the command
    C. Try to resolve the command … to an IP address
    D. Try to correct the command
    E. show error message
    I picked C
    8. Which symbol ping of the following is for unknown packet?
    A. .
    B. *
    C. ?
    D. U
    I picked A
    9. Which cables could be used for star topology? (choose two)
    A. 10 Base T
    B. 100 Base T
    C. 10 Base 5
    D. 10 Base 2
    I picked A and B
    10. Which of the following true about dynamic route?
    A. Reduce CPU of the network
    B. More secure than static
    C. Complicate the maintenance
    D. Allow fast convergence when fail happen
    Did not see this question
    11. What RIPv2 use to elect of route?
    A. Hope count
    B. Administrative distance
    C. Bandwidth
    D. ……
    I picked A
    12. Which of the following are two local host characters?
    A. 32/prefix
    B. 255.255.255.0
    C. The administrative distance is 0
    D. Dynamically learned
    E. ….I forgot the wording, but something like local route
    I picked A and D
    13. Which attributes change all the path way (choose two)
    A. MAC destination address
    B. MAC destination address
    C. IP Source address
    D. IP Source address
    I picked A and B
    14. Question asking when the host sending request (my question was something about why a host uses DNS server………..)
    A. DNS client request to server
    B. To resolve IP to FQDN
    C. To resolve FQDN to IP
    D. Assign IP
    E. Verify connection
    I picked C
    15. Which request used to resolve …….
    A. Send DNS request to DNS server
    B. Send DNS request to DHCP server
    C. …….
    I picked A

    Good luck!

  73. Just passed ICND1 today 930 points
    November 28th, 2017

    Some more ….

    Syslog – what does not belong?

    A. host name
    B. severity
    C. timestamp
    D. message

    What is the maximum size of an Ethernet frame that uses 802.1Q tagging?

    A. 1514 bytes
    B. 128 bytes
    C. 68 bytes
    D. 1522 bytes

    Which option does the route 0.0.0.0/0 represent?

    A. Route with the lowest administrative distance
    B. Gateway of last resort
    C. Null route
    D. Empty routing table

    What is the purpose of a standard access list?

    A. to filter traffic based on destination address
    B. to deny traffic
    C. to filter traffic based on source address

    If you are in VLAN 10 and it gets a packet from VLAN 2 with 802.1q enabled, what does it do with the packet?

    A. Drops the packet
    B. forwards it to VLAN 2
    C. configures the port to handle traffic from VLAN 2
    D. adds it to the VLAN database

    Drag drop question about cable types

    Answer:

    Coaxial 10 base 2
    Twisted 10/100/1000 base
    Fiber BASE-5 BX
    USB connects two computers
    Crossed-over devices of the same type

    Which syslog severity level logs informational messages?

    A. 2
    B. 6
    C. 4
    D. 0

    What is the binary of the IPv6 multicast address

    Answer: 11111111

    What is the lowest AD (IS-IS, IBGP, EIGRP, RIPv2 or OSPF)?

    Answer: EIGRP

    Which destination IP address can a host use to send one message to multiple devices across …?

    A. 239.255.0.1
    B. 172.20.1.0
    C. 192.168.0.119
    D. 127.0.0.1

    Which statement describes the effect of exec-timeout 30 command?

    A. The router disconnects the user session if it is inactive for 30 minutes
    B. The router maintains a user session indefinitely after it is active for 30 mins
    C. The router disconnects a user session if it is inactive for 30 seconds
    D. The router maintains a user session indefinitely after it is active for 30 seconds.

    Which network configuration allows a switch to send traffic from multiple VLANS over a single link to a router that routes between the VLANs?

    A. Port channel
    B. Router-on-a-stick
    C. Virtual trunking
    D. Spanning-tree

    Which statement about native VLAN traffic over 802.1Q trunk is true?

    A. It is discarded by STP
    B. It is placed is a high-priority queue
    C. It is tagged with a value of 1
    D. It is untagged

    When a router makes a routing decision for a packet that is received from one network and destined to another, which portion of the packet does it replace?

    A. Layer 4 protocol
    B. Layer 3 IP address
    C. Layer 2 frame header and trailer
    D. Layer 5 session

    Which protocol can identify connected devices within a mixed-vendor infrastructure?

    A. Virtual terminal protocol
    B. Network time protocol
    C. Link level discovery protocol
    D. Cisco discovery protocol

    Which interface configuration is used with a router-on-a-stick configuration?

    A. VRF
    B. Subinterfaces
    C. PIM sparse mode
    D. Passive-interface

    That’s all I can remember. Good luck to all.

  74. sam
    November 28th, 2017

    congrats buddy, do you remember what you had picked for the DHCP sim questions ?

  75. Just passed ICND1 today 930 points
    November 28th, 2017

    Yes.
    1. R2 configured as DHCP, R3 cannot received an IP. Test takers need to read the configuration by running the “show run” command on both routers. In my case, it was the mis-configuration of router R2.

    2. R1 connected to ISP and configured NTP server 206……R2 cannot sync with R1. In my case, R2 NTP was not configured.

    3. A host in R2 cannot access to Server1 in R1. Carefully review the output of R1 and R2. In my case, R1 has a deny access list that blocks R2 network.

    4. Users complaints that they cannot access to the internet. My answer was “NAT was configured incorrectly on interfaces”

  76. Sunil kumar
    November 28th, 2017

    Congratulation Bro ,Thank you very much .

    pl share which sim in exam .

  77. lab_guy
    November 28th, 2017

    Just passed with a mid 900. I used CBTnuggets (free 7 day trial), Safari books online, 9tut and bought 3 routers and 3 switches for <$150 to practice labs on. I would say 80% of my questions were from 9tut (mostly the ones above and 5 or 6 from the bank of questions). I had 2 sims and they were the same as "Just passed ICND1 today 930 points" above. But they were easy as long as you know how to configure DHCP, NTP, ACL, and NAT. Spend some time with a lab kit or virtual lab and practice that stuff because you'll be doing yourself a disservice if you can't actually configure that stuff when you get a networking job!

  78. Omar
    November 29th, 2017

    @FlashMemory thank u i really appropriated i just pass my exam
    i hv this Q and gets me confused about it

    which ip address in the same layer 2 domain as 192.168.161.10/19

    A-192.168.128.10
    B-192.168.160.10
    C-192.168.192.10
    D-192.168.224.10

  79. Anonymous
    November 29th, 2017

    It will be B

  80. James
    November 29th, 2017

    Hi congratulations Omar, did you get all of the questions from here or did you see any new questions?

  81. Sunil
    November 30th, 2017

    Congratulation Omar ,

    Pl share new questions .

  82. Omar
    November 30th, 2017

    @Anonymous thank u that was my answer but i dont know if it wrong or righ

  83. Omar
    November 30th, 2017

    @Sunil@James sure
    i got 90% of my questions from here labs was easy focus on NAT,NTP,DHCP,ACL and do ur practice on it but dont waste much time on it just do the sims from here and get use of show run command

  84. James
    November 30th, 2017

    Thanks Omar, do you recall any of the questions that were not here?

  85. sam
    December 2nd, 2017

    hey guys just passed today with 900, it was my second attempt as you might know, all the questions still valid, the DHCP still the same with the same configuration, they just reworded some of the questions and add few, I’ll posted later, if you have any questions feel free to ask here, stay tuned I’ll share my ICND2 experience on one of those ICND2 new questions part once I take it !! good-luck everyone.

  86. icnd1
    December 2nd, 2017

    Hey Sam! Congrats!! How many percentage of your questions came from the 9tut dumps?

  87. James
    December 3rd, 2017

    Which statement is true about port-security violations is true?

    A. When a violation occurs on a switch port in restrict mode, the switch port continues to accept traffic from unknown MAC address until the administrator manually disables it.
    B. When a violation occurs on a switch port in protect mode, it sends a syslog notification message
    C. A port In the err-disabled state must be re-enabled manually, if recovery is disabled
    D. When a switch port is in protect mode, it allows traffic from unknown MAC address until it has learned the maximum allowable number of MAC addresses

    Answer: C
    Can anyone explain why D is not the correct answer? if the maximum allowable number of MAC was 10 for example, the switch will continue forwarding the traffic until it learns all the different
    10 MAC addresses. And what is the purpose of having Recovery in option C if you need the port security option?
    Thanks,

  88. sam
    December 4th, 2017

    1. Which router source code represent the routing protocol with a default administrative distance of 90 in the routing table?
    A. S
    B. E
    C. D
    D. R
    E. O

    2. Which of the following is true about port security?

    A. In stick, port retrain dynamically learned
    B. Configure spanning destination
    C. The default configuration with max 10
    D. Not supported by VLAN

    3. Which device can be used to extend the LAN without using layer3 device?
    A. Access point
    B. Switch
    C. Wireless controller
    D. Firewall
    “they just reworded the question in different way, last time was like: 4. Which of the following true about access point?”
    4. Which six-byte field in a basic ethernet frame must be an individual address?
    A. FCS
    B. SOF
    C. Sa
    D. Da

    5. Which layer of TCP/IP combine the physical and datalink layers of the OSI model?
    A. Internet layer
    B. Transport layer
    C. Application layer
    D. Network access layer

    That’s pretty much what I’ve found on my test as well as the 15 qts that I post before

  89. sam
    December 4th, 2017

    @Icnd1 thank you, I’d say that most of the questions from the comments here, may be like 40%, and 25% from 9tut pdf dumps, the sim still valid like I said,and sure you’ll have a few new questions, but its so easy as long as you know the concept, good-luck.

  90. James
    December 4th, 2017

    Hello Sam, when you say from 9tut pdf dump, how do you get that. Thanks

  91. sam
    December 4th, 2017

    send an email to support at9tut.com, it is just the questions for the published answers of 9tut

  92. icnd1
    December 4th, 2017

    Hello Sam! I am a little bit confused now. That 9tut pdf dump does not include any new questions, right? It only includes the questions they already have here on the website, just in a pdf format? Or am I wrong? 🙂

  93. sam
    December 4th, 2017

    @Icnd1 yes buddy right, thats why we are trying to post the new ones here 🙂

  94. icnd1
    December 4th, 2017

    Thanks Sam!

  95. Passed Today
    December 5th, 2017

    50% was from above and 50% from the question banks…..Sims where exactly like “Just passed ICND1 today 930 points” stated above. No new questions…. just a lot of rewording in the answers.

  96. SLIME
    December 5th, 2017

    Passed few days ago, got 930.
    Do the flash based questions few times, write down what you miss and study on that, go through the new ICND1 v3 questions 1 time and study them, and walk it through again just before the test, and you are good to go.

    Most of the questions are on here, i had like 55 questions, maybe 2-3 i did not recognize, they may not all be exactly the same as here, but alot of them are, just that some questions are asked in a different way.

    I had both dhcp and security sim, and it was exactly the same.

  97. Anonymous
    December 5th, 2017

    Anyone with recent dumps should please assist.

  98. James
    December 6th, 2017

    @Sam, what were your answers for the questions you shared above?
    Thanks,

  99. Michael
    December 6th, 2017

    Hi guys,

    Are there any new questions? I have tomorrow exam and I hope I will pass the exam with the Sims and questions ons 9tut!

  100. Michael
    December 7th, 2017

    About the question: Which forwarding technology stores destination addresses in the cache?

    Why is it CEF and not Fast Switching?

Comment pages
1 2 3 4 897